Function Mode - Ayrton WildSun 500 Mode D'emploi

Set Dmx Address A001~AXXX
Value Display PAN...
Set To Slave Slave1,Slave2,Slave3
Auto Program Master / Alone
Music Control Master / Alone
Time Information Current Time
Total Life Hours
Last Run Hours
Timer Password
Clear Last Run
Temperature Info Head Temperature
Software Version Ver 1.0
Status Settings Address via DMX
No DMX Status
Pan Reverse
Tilt Reverse
Pan Degree
Feedback
Movement Speed
Zoom Speed
Mic Sensitivity
Hibernation
Fans Control Head Control
Base Control
Display Setting Shutoff Time
Display Reverse
Key Lock
Temperature C/F Celsius
Fahrenheit
Initial Effect PAN
Wireless DMX De-Act WDMX
Activate WDMX
Act & Data Out
Rest WDMX Mem
Reset Default ON/OFF
Reset All
Reset Pan&Tilt
Reset Zoom
Test Channel PAN
Manual Control PAN
Calibrate Values --Password--
PAN
:
User Mode Standard Mode
Basic Mode
Extended Mode
User Mode A
User Mode B
User Mode C
Edit User Mode PAN
Select Programs Auto Pro Part 1 Program 1 ~ 10 Program 1
Auto Pro Part 2 Program 1 ~ 10 Program 2
Auto Pro Part 3 Program 1 ~ 10 Program 3
Edit Program Program 1 Program Test
: Step 01=SCxxx
Program 10 Step 64=SCxxx
Edit Scenes
Edit Scene 001 Pan,Tilt,......
~ Edit Scene --Secne Time--
250 Input By Outside
Rec. Controller XX~XX

Function mode

Set DMX Address
With this function, you can adjust the desired DMX-address
via the Control Board.
1. Access the main menu.
2. Tap the <Up/Down> button until "Set DMX Address" is
displayed.
3. Press ENTER, the display will show "Set DMX Address".
4. Tap the <Up/Down> button, the display will show
"A001~AXXX"
5. Press ENTER to confirm or press <MODE/ESC> to
return to the main menu.
DMX address setting
DMX value display
Slave setting
Auto program
Music control
XXXX(Hours) Power on running time
XXXX(Hours) Fixture running time
XXXX(Hours) Fixture Last times clear
Password=XXX Timer Password 038
ON/OFF Clear Fixture Last time
XXX °C / °F Temperature in the head
Software version of each IC
ON/OFF Add. via DMX
Close/Hold/Auto/Music Auto run if no DMX
ON/OFF Pan Reverse movement
ON/OFF Tilt Reverse movement
630/540 Pan Degree Select
ON/OFF Movement Feedback switch
Speed 1~ 4 Movement Mode Select
Speed 1~ 2 Zoom Mode Select
0~99% Sensitivity of Mic.
OFF/1~99M 15M Standby mode
Auto Fans Speed Head Fans Speed Mode
High Fans Speed Select
Low Fans Speed
10% Base Fans Speed Mode
30% Select
50%
02~60m 05m
ON/OFF
ON/OFF
Temperature switch between
°C / °F
PAN =XXX Initial effect position
De-activate WDMX
Activate WDMX
Act & Data Out
Reset Wireless DMX Mem
Restore factory sett.
Reset all motors
Reset Pan&Tilt
Reset Zoom
Test function
PAN =XXX Control the light
Password=XXX Calibrate and adjust the
PAN=XXX effects to standard/right
: position Password "050"
User's mode to change
channel numbers
PAN = CH01 Preset User modes
Select programs to be run
("STEP XX") Testing program
Program in loop
Save and exit
Save and automatically return
Pan=xxx......
TIME=xx.xs
manual scenes edit
Automat. scenes rec
USER MANUAL
Value Display
With this function you can display the DMX 512 value of each
channel. The display automatically shows the channel with a
value changing.
1. Access the main menu.
2. Tap the <Up/Down> button until "Value Display" is
displayed.
3. Press ENTER, the display will show "Value Display".
4. Tap the <Up/Down> button, choose each channel.
5. Press ENTER to confirm or press <MODE/ESC> to
return to the main menu.
Set to slave
With this function, you can define the device as slave.
1. Access the main menu.
2. Tap the <Up/Down> button until "Set To Slave" is
displayed.
3. Press ENTER, the display will show "Set To Slave".
4. Tap the <Up/Down> button, the display will show
"Slave1", "Slave2", "Slave3".
5. Press ENTER to confirm or press <MODE/ESC> to
return to the main menu.
Auto Program
With this function, you can run the internal program. You can
select the desired program under "Select program". You can
set the number of steps under "Edit program". You can edit
the individual scenes under "Edit scenes". With this function,
you can run the individual scenes either automatically, i.e.
with the adjusted Step-Time.
1. Access the main menu.
2. Tap the <Up/Down> button until "Auto Program" is
displayed.
3. Press ENTER, the display will show "Auto Program".
4. Tap the <Up/Down> button, the display will show
"Master1", " Alone".
5. Press ENTER to confirm or press <MODE/ESC> to
return to the main menu.
Music control
With this function, you can run the internal program sound-
controlled.
1. Access the main menu.
2. Tap the <Up/Down> button until "Music control" is
displayed.
3. Press <ENTER>, the display will show "Music control".
4. Tap the <Up/Down>button, the display will show
"Master1", " Alone".
5. Press <ENTER> to confirm or press <MODE/ESC> to
return to the main menu.
9