Error Message; Pan - Movement Er; Tilt- Movement Er; Cleaning And Maintenance - Ayrton WildSun 500 Mode D'emploi

Error message

When you turn on the fixture, it will make a reset at first.
The display may show "Err channel is XX" while there are
problems with one or more channels. "XX" stands for channel
1, 2, 3, 4, 5, 6 who has the testing sensor for positioning.
For example, when the display shows "Err channel is Pan
movement", it means there is some error in channel 1. If there
are some errors on channel 1, channel 3, channel 23 at the
same time, you may see the error message "Err channel is
Pan movement", "Err channel is Tilt movement", "Err channel
is Zoom" flash repeated for 2 times, and then the fixture will
generate a second reset. If the fixture remain error message
after performing reset more than 2 times, only the channels
which have errors can not work properly, others can work as
usual. Please contact with dealer or manufacturer for service,
self repair is not allowed.

PAN - movement Er

(PAN-head movement error) This message will appear
after the reset of the fixture if the head's magnetic-indexing
circuit malfunctions (sensor failed or magnet missing) or the
stepping-motor is defective (or its driving IC on the main PCB).
The TILT- movement is not located in the default position after
the reset.

TILT- movement Er

(TILT-head movement error) This message will appear after
the reset of the fixture if the head's magnetic-indexing
circuit malfunctions (sensor failed or magnet missing) or the
stepping-motor is defective (or its driving IC on the main PCB).
The TILT- movement is not located in the default position after
the reset.

Cleaning and maintenance

The following points have to be considered during the
inspection:
All screws for installing the devices or parts of the device
have to be tightly connected and must not be corroded.
There must not be any deformations on the housing,
color lenses, fixations and installation spots (ceiling,
suspension, trussing).
Mechanically moved parts must not show any traces of
wearing and must not rotate with
unbalances.
The electric power supply cables must not show any
damage, material fatigue or sediments.
Further instructions depending on the installation spot and
usage have to be adhered by a skilled installer and any
safety problems have to be removed.
CAUTION !
Disconnect from mains before
starting maintenance operation
We recommend a frequent cleaning of the device. Please
use a moist, lint- free cloth. Never use alcohol or solvents.
There are no serviceable parts inside the device. Please refer
to the instructions under "Installation instructions".
Should you need any spare parts, please order genuine parts
from your local dealer.

Technical specifications

Optics

4:1 zoom optics system
75% optic efficiency
Beam aperture: from 11° to 45°
Motorised linear zoom

Source

31 Multi-chip High-Power LEDs sources
Light output: up to 10.000 lumen
Rated Sources life: 25.000 hours
Flicker free sources Management, convenient for TV
applications and all video recorded events

Movement

Extremely accurate positioning
Moving-head operated via either
or 8/16 bit resolution
High-resolution stepper motors operated via microprocessors
ensure extreme accuracy and smooth movements
PAN and TILT automatic repositioning
Moving head range: 540° (PAN), 270° (TILT)

Colours

Sophisticated 4 colours RGB+W mixed, reaching high Colour
Rendering Index
Uniform light beam with no colour shadows, and rich
saturated colour-hues
8 or 16 bit resolution
4,29 billion colours (8 bit resolution)
Virtual colour wheel including White presets
Pre-programmed colours and rainbow effect

Dimmer, strobe

Electronic dimmer for adjustment of light output from 0 to
100% with no colour variation (16 bit)
High-speed white or full colour strobe effect with variable
1-25 fps flash rate
Pre-programmed variable strobe effect
18 USER MANUAL