Emission Levels - Festool PLANEX LHS 2 225 EQI Notice D'utilisation

English
Keep bystanders a safe distance away
–
from work area. Anyone entering the work
area must wear personal protective
equipment. Fragments of workpiece or of a
broken accessory may fly away and cause
injury beyond immediate area of operation.
Hold the power tool by insulated gripping
–
surfaces, because the sanding surface
may contact its own cord. Cutting a "live"
wire may make exposed metal parts of the
power tool "live" and could give the opera­
tor an electric shock.
Position the cord clear of the spinning ac­
–
cessory. If you lose control, the cord may
be cut or snagged and your hand or arm
may be pulled into the spinning accessory.
– Never lay the power tool down until the
accessory has come to a complete stop.
The spinning accessory may grab the sur­
face and pull the power tool out of your
control.
– Do not run the power tool while carrying it
at your side. Accidental contact with the
spinning accessory could snag your cloth­
ing, pulling the accessory into your body.
Regularly clean the power tool's air vents.
–
The motor's fan will draw the dust inside
the housing and excessive accumulation of
powdered metal may cause electrical haz­
ards.
Do not use accessories that require liquid
–
coolants. Using water or other liquid cool­
ants may result in electrocution or shock.
2.3 Further safety instructions
– Harmful/poisonous dust may be produced
when working (e.g. paint products con­
taining lead and some types of wood).
Contact with or inhalation of this dust may
pose a risk for the operating personnel or
persons in the vicinity. Comply with the
safety regulations that apply in your coun­
try. Connect the power tool to a suitable
dust extractor.
– Wear at least a P2 respiratory mask to
protect your health. Ensure there is ade­
quate ventilation in enclosed spaces.
Use a residual-current circuit break­
–
er (RCCB) or an isolating transformer if
operation of the power tool in a damp en­
vironment cannot be avoided. In the event
of an electric shock, the residual-current
circuit breaker (RCCB) or isolating trans­
former protects you against life-threaten­
ing current through the body.
20
– If potentially explosive or self-igniting dust
is produced during sanding, the machining
instructions issued by the material manu­
facturer must always be followed.
Caution: Fire hazard! Prevent the material
–
being sanded and the sander from over­
heating. Always empty the dust container
before taking breaks from work. Grinding
dust in the filter bag and/or in the filter of
the mobile dust extractor may ignite spon­
taneously under unfavourable conditions,
such as flying sparks, when sanding. There
is a particular risk if the sanding dust is
mixed with clear coats or polyurethane res­
idues or other chemical substances and the
material being sanded becomes hot after it
has been worked on for a long time.
– Metals and materials that contain asbes­
tos must not be processed. Sparks may be
created in the dust bag when processing
metals. This increases the risk of fire.
Hold the power tool firmly with both hands
–
and maintain a stable stance when per­
forming work. Using both hands ensures
that the power tool is guided safely, see
Section 8.1
Warning of harmful light radiation.
–
Do not look into the light beam for long
periods. Do not direct the light beam to­
wards other people or animals. Optical ra­
diation can damage the eyes.
– Always use an antistatic suction hose (AS)
with the power tool. A slight electric shock
may cause you to panic briefly and become
distracted, which may result in an accident.
Always use original Festool backing pads.
–
Pads from other manufacturers can break.
Only for AS/NZS: The tool shall always be
–
supplied via residual current device with a
rated residual current of 30 mA or less.
2.4

Emission levels

The levels determined in accordance with
EN 62841 are typically:
LHS 2 225 EQI/LHS 2 225 EQ
Sound pressure level
Sound power level
Uncertainty
L = 86 dB(A)
PA
L = 97 dB(A)
WA
K = 3 dB