Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
GB
ENGLISH
Service Mode
The room temperature unit has a menu to change the parameters.
In order to enter this menu press and hold the edition key
10 seconds.
Note that the clock setting mode is first shown. Hold the
down until the service menu is displayed.
Now you can select a parameter with the navigation keys
or
. Modify the value with the (+) and (-) keys and
press OK. To leave the parameter menu, choose parameter 99 End
and press OK.
Keyboard's Lock Function
This function prevents unauthorized changes of your settings.
•
To activate the keyboard's lock function, press and hold
and
simultaneously.
•
Repeat the same procedure to unlock the keyboard
Airing
If the room unit detects a sudden drop in temperature the unit will
disregard this for the next half hour. Decimal point and temperature
unit blink.
Remote Control
By connecting a GSM modem to the room unit, it can be remote-
controlled via mobile phone. Press (+) or (-) or select a new
operating mode to end the remote control session.
A terminal block is positioned on the back of the room temperature unit.
Please note that only voltage- and potential-free contacts are to
be connected.
Trouble Shooting
Note that when a temperature setting has been changed it will take
hours before the room temperature corresponds to the new
setting due to dimensions of the heating system and insulation of
the house.
If the room temperature unit works but the room temperature is
not in accordance with the program:
•
Check the time setting
•
Check that the program step is not too short
•
Check that the difference between comfort and reduced
temperature is not too high
Otherwise do the trouble shooting according to the list in the
LK 110/LK 120/LK 130 SmartControl Instruction Manual.
Error codes: shown on the display
10
Internal error
11
Supply temperature sensor
12
Outdoor sensor
13
Reserve
14
Room temperature unit, communication error
15
Reserve
50
Room temperature unit, room temperature sensor
will now appear on the display.
No Parameters and Functions
10
bEd: (+) or (-) to set the desired temperature for
for
programs P1-P9
11
key
Out: (+) or (-) to set the desired temperature for
programs P1-P9
12
InP: (+) or (-) to set the desired temperature for
remote operation .
Diagnostic function:
shows closed contact.
20
deG: Temperature units - °C Celsius or °F Fahrenheit
21
Time format 24H (24:00) or 12H (12:00 AM/PM)
22
dSt: Summer time change. YES automatic change. no
manual change of time. Date is not used.
30
AirC: Calibration of the room temperature display
±5°C/±8.5°F. The calibration should be done after 1 day's
operating with the same set temperature. Place a thermo-
meter close to the controller and check the temperature in the
room after 1 hour. When you enter the calibration parameter,
no is displayed to indicate that no calibration has been made.
To enter the value shown on the thermo-meter, use (+) and
(-) keys to enter the real value. Then press OK to confirm. The
message YES is displayed and the value will be stored in the
internal memory. You can cancel the calibration by pressing
OK and then
31
OutC: Calibration of outdoor temperature sensor
±10°C/±17°F. The same calibration procedure described for
30 AirC, except for the location of the thermometer.
80
Clr ALL: Resetting to factory settings.
Note: Ensure that you have all necessary informa-
tion to reset your installation before using this function.
Press and hold the OK key for 10 seconds to reset tempera-
tures and parameters in this menu to factory settings. User
programs will also be reset.
90
Software version
99
End: Press the OK key to exit parameter menu and return to
normal operation.
Reservations for product improvements.
Schedule for user's program
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
The frame around the symbol
.
° C
1 2 3 4 5 6 7
° F
° C
1 2 3 4 5 6 7
° F
° C
1 2 3 4 5 6 7
° F
° C
1 2 3 4 5 6 7
° F
° C
1 2 3 4 5 6 7
° F
° C
1 2 3 4 5 6 7
° F
° C
1 2 3 4 5 6 7
° F
° C
1 2 3 4 5 6 7
° F
° C
1 2 3 4 5 6 7
° F
in
in
during
March
15
9
Publicité
Table des Matières
