GRE Vermela Notice De Montage page 53

POSITIONING OF THE SEALING PIECES
EN
A B C
REFILLING FITTING WITH KEY
Start filling the pool with water, up to 4 cm. from the lower edge of the valve hole.
Mark the hole with a felt tip pen (A) and cut a cross in the centre of the opening (B) with a cutter (BLADE),
without going over the hole of the die cut.
From inside the pool, insert through the cut (C), the return valve (No. 1) with one of the friction rings (No. 2)
and one of the seals (No. 3). The pieces of liner that stick out through the outer part of the pool, should be cut
cleanly and accurately.
The other gasket (No 3.1) is placed from the outside, folding it, so that it is in contact with the liner and the
panel.
Place the other friction ring (No 3.1) and tighten firmly with the nut. Thread the connector tube previously
prepared with Teflon into the body of the nozzle, from outside of the pool.
Insert the return hose which goes from the outlet of the treatment unit to the return valve, and secure it with
the clamp.
Important: Before placing the hose, insert the trim. (No 5)
Make sure that the filter apparatus valve is in the CLOSED position.
5
1- Body of the nozzle
2.1
3.1
2- 2.1 Round flat seal
3- 3.1 Seal
4- Nozzle body nut
5- Trim
SKIMMER
ASSEMBLING THE SKIMMER
Before installing the skimmer to the pool, the gate unit must be installed in the skimmer opening
Then place the seal (No. 6) and the conical opening (No. 7), bolting the parts with 8 screws (No. 8) DIN7982 5,5x25 , as indicated in A.
ANCHORING THE SKIMMER
Continue filling the pool with water until it reaches a level of 4 cm. under the die-cut of the skimmer of the pool wooden.
Cut the liner using the cutter (blade) following the line of the die cut.
104
D E
Look for us in our YouTube
channel to help you with
the assembly.
Install the filter before continuing with
cutting the liner.
5
6
A
7 7
SKIMMER
8
A
• Before continuing, make sure that the skimmer flap is well positioned.
• Mark the position of the fixing screws on the liner with a felt-tip pen.
• (B) Position the second rectangular flat seal (5.1) and the flange (8) against the liner, aligning the holes with the position marks of the screws.
• Fix the flange (6) on the liner with 18 screws (7) starting at the bottom(C). The pressure of fixing points on the liner should be constant, (fixing in cross
• Screw slightly at first to make sure they fit properly, then fully tighten them, following the order indicated in (C)
• Press on the trim cover No. 9, taking care to place the level mark in the correct position (D).
• Use Teflon to bolt the hose adapter (11) to the lower hole of the skimmer body, and then connect the suction hose and tighten with a clamp. (E)
• Cut the liner with a cutter from the inside of the skimmer.
• Now you should install the filter.
6
5 8
10
7
13
11
D
1
3
B C
8
1
9
17 15 13 12
7
10
8
6 4 2 1
9
Look for us in our YouTube
channel to help you with
the assembly.
1- Skimmer cover
2- Suction cover
3- Basket
4- Gate unit
5- Connection seal
6- Conical opening
7- Bag of screws (26 DIN 7982 5,5X25 and 10DIN 7982 4,8X19)
8- Gasket
11 12
9- Flange with trim cover
10- Return valve
11- Winter storage plug
12- Key
13- Hose adapter
E
9
EN
14 16 18
11
9
3 5 7
105