General Information; Safety - Pentair HYDROMATIC P33A1 Notice D'utilisation

Safety

DescriPtion
This Pedestal Sump Pump is designed for home
sumps. Unit is equipped with a 3-prong grounding-
type power cord. Sleeve bearings on motor shaft never
need lubrication. Automatic reset thermal protection.
notice: This unit is not designed for applications
involving salt water or brine! Use with salt water or
brine will void warranty.
sPecifications
Power supply required ........................... 115V, 60 HZ.
Horsepower ............................................................. 1/3
Motor duty .................................................. Intermittent
Liquid Temp. Range .................. 32°F to 70°F(0°-21°C)
Individual Branch Circuit
Required GFCI Class A ................................... 15 Amps
Motor full load (maximum) ........................... 3.5 Amps
Discharge: Plastic Models ......................1-1/4" FNPT
Cast Iron Models ..................1-1/2" FNPT
Performance
GPH (LPH) AT TOTAL FEET (M)
5 Ft. 10 Ft.
(1.52) (3.05)
3000 2460
(11 355L) (9 312L)
General safety
Electrically powered sump pumps normally give
many years of trouble-free service when correctly
installed, maintained, and used. However, unusual
circumstances (interruption of power to the pump,
dirt/debris in the sump, flooding that exceeds the
pump's capacity, electrical or mechanical failure
in the pump, etc.) may prevent your pump from
functioning normally. To prevent possible water
damage due to flooding, consult your retailer about a
secondary AC sump pump, a DC backup sump pump,
and/or a high water alarm. See the "Troubleshooting
Chart" in this manual for information about common
sump pump problems and remedies. For more
information, see your retailer or call Hydromatic
customer service at 1-888-957-8677.
1. Know the pump application, limitations, and
potential hazards.
Do not use in explosive
atmospheres. Pump water only
with this pump. failure to follow this warning can
result in personal injury and/or property damage.
2. Disconnect power before servicing.
3. Release all pressure within system before servicing
any component.
4. Drain all water from system before servicing.
risk of flooding. if a flexible
discharge hose is used, pump
may move when motor starts. If it moves far
enough so that switch hits side of sump, switch
may stick and prevent pump from starting.Make
sure pump is secured so it cannot move around in
sump.
5. Secure discharge line before starting pump. An
unsecured discharge line will whip, possibly
causing personal injury and/or property damage.
6. Check hoses for weak or worn condition before
each use, making certain all connections are
secure.
15 Ft. 20 Ft.
(4.57) (6.09)
1620 0
(6 131L) (0L)
7. Inspect sump, pump and system components
monthly. Keep free of debris and foreign objects.
Perform routine maintenance as required.
motor or switch linkage. Keep all flammable
objects or liquids away from motor.
8. Provide means of pressure relief for pumps whose
discharge line can be shut-off or obstructed.
9. Personal Safety:
a. Wear safety glasses at all times when working
with pumps.
b. Keep work area clean, uncluttered and
properly lighted – replace all unused tools and
equipment.
c. Keep visitors at a safe distance from work
area.
d. Make workshop child-proof – with padlocks,
master switches, and by removing starter keys.
10. When wiring an electrically driven pump,
follow all electrical and safety codes, as well as
most recent National Electrical Code (NEC) and
Occupational Safety and Health Act (OSHA).
11. This equipment is only for use on 115 volt
(single phase) and is equipped with an approved
3-conductor cord and 3-prong, grounding-type
plug.
connected to properly grounded, grounding-type
receptacle.
live terminal!
Where a 2-prong wall receptacle is encountered,
it must be replaced with properly grounded
3-prong receptacle installed in accordance with
the National Electrical Code and local codes and
ordinances.
12. All wiring should be performed by a qualified
electrician.
13. Make certain that power source conforms to
requirements of your equipment.
14. Protect electrical cord from sharp objects, hot
surfaces, oil, and chemicals. Avoid kinking
cord. Replace or repair damaged or worn cords
immediately.
15. Do not touch an operating motor. Modern motors
can operate at high temperatures.
16. Do not handle pump or pump motor with wet
hands or when standing on wet or damp surface,
or in water.
if your basement has water or
moisture on floor, do not walk on
wet area until all power has been turned off. if shut-
off box is in basement, call electric company to shut-
off service to house, or call local fire department for
instructions. remove pump and repair or replace.
failure to follow this warning can result in fatal
electrical shock.
Do not use in hazardous or
explosive locations.
california Proposition 65 Warning
This product and related accessories
contain chemicals known to the State of California
to cause cancer, birth defects or other reproductive
harm.
fire HaZarD - Do not store
or rest objects on or near
to reduce risk of electric
shock, be certain that it is
never connect green (or green
and yellow) wire in cord to a
3