Télécharger Imprimer la page

Güde TK 2400 P Traduction Du Mode D'emploi D'origine page 29

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 31
f) Keep cutting tools sharp and clean.Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Electric tools, accessory equipment, extensions,
etc. to be used in accordance with these Instruc-
tions. consider the working conditions and the
activity being performed. Using electric tools for
purposes other than those specified may lead to
dangerous situations.
5) Service
a) Have your electric tools repaired by qualified autho-
rised staff only, using original spare parts only. The
safety of electric tools will be maintained by this.
Safety instructions Circular table
saw
Operation is only allowed with a safety
switch against stray current (RCD max. stray
current of 30mA).
wear ear protectors. Exposure to noise can cause
hearing loss.
warning wear gloves when handling saw blades and
rough materials.
warning The dust produced when using this tool may
be harmful to health. Do not inhale the dust. Use
a dust absorption system and wear a suitable dust
protection mask. Remove deposited dust thoroughly,
e.g. with a vacuum cleaner.
The machine must be during operation inside buil-
dings connected to external device dedusting chips
and dust. Dedusting device must be put in operation
prior the work start.
before use check machine, cable, and plug for any
damages or material fatigue. Repairs should only be
carried out by authorised Service Agents.
Always use the protective shields on the machine.
The protective equipment on the appliance is strictly
prohibited to be disassembled, changed, used in con-
flict with the designation and it is prohibited to attach
any protective equipment of other manufacturers.
check all screw and plug-in connections and protec-
tive equipment if firm and tightened properly and
whether all moving parts are running smooth whene-
ver the appliance is to be put into operation.
Any faults with the machine, including any related to
the safeguard or the saw blades, must be reported to
the persons in charge of safety as soon as the faults
are discovered.
For security, use devices such as safety- and pressure
device, guide slide, rip fence, etc.
During round timber cutting it is necessary to fix the
workpiece against rotation by means of fixing tool
and use circular saw type suitable for cross cuts.
Do not use circular saws for cutting slots (grooves in
workpiece).
cutting rebates or grooves is only permitted with a
suitable protective device fi tted, e.g. a protective
tunnel over the saw table.
Support large panels to minimise the risk of blade
pinching and kickback. Large panels tend to sag un-
der their own weight. Supports must be placed under
the panel on both sides, near the line of cut and near
the edge of the panel.
warning Sawdust and splinters must not be removed
while the machine is running.
Replace the table insert when worn
Do not use saw blades which are damaged or
deformed
The teeth thickness, or the set of the teeth must be
thicker than the body of the blade and the riving
knife. Do not remove the riving knife.
It is necessary to select a saw blade which is suitable
for the material being cut.
Do not use saw blades not corresponding to the key
data given in these instructions for use.
Only use tools that meet standard EN 847-1.
Only use saw blades which have been properly
sharpened. It is essential to adhere to the maximum
speed specified on the saw blade.
Do not use saw blades made of high-speed steel.
Transport and store the tools in a suitable container;
maintenance
before carrying out any work on the machine,
disconnect the plug from the socket.
Prior to every use, visually check the machine to rule
out any defects, in particular on the power cable and
the plug.
waRNING The machine must not be used under any
circumstances if the machine or the safety devices are
damaged.
Refer all servicing to customer service.
Use only original accessories and original spare parts.
Only a regularly maintained and treated appliance
can serve as a satisfactory aid. Insufficient mainte-
nance and care can lead to unforeseen accidents and
injuries.
ENGLISH
23

Publicité

loading

Ce manuel est également adapté pour:

55167