Ritter E 16 Mode D'emploi page 8

English
slIcING
caution:
– Never touch the rotating
blade (11) when the appli-
ance is operating!
– Do not use it to cut frozen
foods, bones, food contain-
ing large stones, roast
meats that are encased in
netting or packaged foods!
– Never allow the appliance to
run for more than 5 minutes
at a time.
– The rotary blade will con-
tinue to run for a short time
after being switched off.
Use the slice thickness adjust-
ment knob (4) to set the required
thickness.
Note:
The slice thickness adjustment
scale is not a millimetre scale.
For safety reasons, the "0"
position is designed to cover the
blade.
Place the food to be sliced
onto the slice carriage (3). Use
the left-over holder (9) to press it
up against the stop plate (2).
caution:
Protect your hands, by always
using the slice carriage and,
where applicable, the left-over
holder. Exception: Excessively
large food to be sliced.
Switch the appliance on using
the rocker switch (1). There are
two operating modes available:
Temporary (Position II): The
rotary blade (11) runs as long as
the switch is pressed and held
down in this position.
Continuous operation (Position I):
The rotary blade runs without the
switch being pressed and held
down until you move the switch to
the "0" position.
Note:
Never use the appliance for more
than a maximum of 5 minutes
continuous operation.
• With the appliance running,
insert the food to be sliced by
slightly feeding it up against the
rotary blade.
• Once slicing has been com-
pleted wait until the rotary blade
has come to a complete stop.
• After each use turn the slice
thickness adjustment knob to the
"0" position, in order to cover up
the sharp rotating blade and to
avoid any injuries.
on model E 16:
Pull the slice tray (5) to the left
and out of the appliance.
cleANING.tHe.
. A pplIANce
caution:
– Switch the appliance off
before cleaning it; pull the
mains plug out off the socket
and turn the slice thickness
adjustment knob (4) to the
"0" position.
– Never immerse the appli-
ance in water.
– Risk of injury: the ro-
tary blade (11) is extremely
sharp!
From time to time the appli-
ance will need to be thoroughly
cleaned, as perishable left-overs
will be left behind the rotary
blade (11).
• Remove the slice tray (5, E 16)
and the left-over holder (9).
Pull the slice carriage (3)
forward and then lift it up and out
of the guide groove.
• Rinse all the removed parts by
hand in warm rinsing water (not
in the dishwasher!).
• Wipe down the housing parts
using a damp cloth.
Note:
Do not use any abrasive cleans-
ers, sponges with rough surfaces
or hard brushes.
Removing the rotary blade:
Place a suitable coin on the
blade catch (10) and turn it in a
clockwise direction.
• Take hold of the rotary blade at
its rotational centre and remove
it.
• Rinse the rotary blade by hand
in warm rinsing water (not in the
dishwasher!)
• Clean the housing behind the
blade using a dry cloth/brush.
stOrAGe
Keep the appliance out of the
reach of children.
To store the cable always use the
cable compartment (8) integrated
into the appliance.
caution:
Never wrap the cable around
the appliance.
DIspOsAl
At the end of its service
life this product may not
be disposed of as part of
normal domestic waste.
It must be taken to a dedicated
collection point for recycling
electrical and electronic devices.
This is indicated by the symbol
on the product, the operating
instructions or the packaging.
The materials can be used again
in accordance with their iden-
tification. The re-use, material-
sensitive recycling or other forms
of recycling of old appliances
enables you to make a vital
contribution to protecting our
environment.
Please consult with the disposal
office at your local authority.
reAch.DIrectIVe
See www.ritterwerk.de
7