Eu Declaration Of Conformity; Conditions Of Warranty - SDMO KOHLER HX3000C Manuel D'utilisation Et D'entretien

8.5 Recommended fuel quality
Using fuel which does not comply with the following specifications exposes the equipment to irreversible damage not covered under
warranty:
- Cleanliness and quality: ensure that the petrol used does not contain water and that it is fresh and clean (not out of date or
contaminated).
- Octane rating: minimum octane rating of 87 (R+M)/2 or minimum octane rating of 90 (RON = Research Octane Number)
- Blends: the use of unleaded petrol containing up to 10% ethyl alcohol is authorised (France: SP95-E10). It is not permitted
to use unleaded petrol containing less than 90% petrol, e.g. E15, E20 or E85. Blends of methyl tert-butyl ether (MTBE) and
unleaded petrol are approved (up to a maximum of 15% MTBE by volume).
However, it is strongly recommended that the same type of fuel is used throughout the complete service life of the unit.
8.6

EU Declaration of Conformity

We, SDMO Industries - 270 rue de Kerervern, 29490 GUIPAVAS/CS 40047, 29801 BREST CEDEX 9 – France, hereby declare
under our sole responsibility that the following generating sets:
Equipment description:
Generating set
1. Comply with the safety requirements set out in the Low Voltage Directive - 2014/35/EU of 26th February 2014 in application of
the harmonized standard EN 60204-1: 2006 (AMD 1 2006, COR 2010)
2. Comply with the provisions of the following Directives:
- Machinery - 2006/42/EC of 17th May 2006 in application of the harmonized standard EN 12601: 2010
- Electromagnetic compatibility - 2014/30/EU of 26 February 2014 in application of the harmonized standards EN 60034-1:
2010 (COR 2010) / EN 61000-6-1: 2007 / EN 61000-6-2: 2005 (COR 2005) / EN 61000-6-3: 2007 (AMD1 2011,
AMD1/COR 12) / EN 55011: 2009 (AMD 1 2010)
This equipment is not designed for use outside an enclosure significantly limiting the transmission of sound (the exhaust gases
must be evacuated outside and adequate ventilation must be provided so that any people or animals present are not affected).
Name and address of the person authorized to create and hold the technical file:
B. GUESTIN, SDMO Industries, 270 rue de Kerervern, 29490 GUIPAVAS/CS 40047, 29801 BREST CEDEX 9 – France.

9 Conditions of warranty

Your unit is covered by a commercial warranty granted by SDMO Industries. This warranty must be applied by the distributor from
which you purchased your unit, in accordance with the following provisions:
TERM:
The warranty for your unit is valid for a period or 36 months or 2500 operating hours, from the date of purchase. It applies to
whichever of these thresholds is reached first. If the unit does not have a working hours counter, the number of operating hours will
be deemed to be eight (8) hours per day.
TERMS FOR APPLICATION OF THE WARRANTY:
The warranty starts on the date the unit was purchased by the first user. This warranty is transferred with the unit if the first user
chooses to transfer it, either free or for a charge; it is valid for the remaining duration of the initial warranty, which cannot be
extended.
The warranty only applies upon presentation of a legible purchase invoice, which states the date of purchase, the unit type, the
serial number, and the name, address and commercial stamp of the distributor. SDMO Industries reserves the right to refuse to
honour the warranty in the absence of documentary evidence of the date and place of purchase of the unit. This warranty entitles
the holder to the repair or replacement of the unit or its components, if deemed to be defective by SDMO Industries after expert
analysis in its workshops; SDMO Industries reserves the right to modify the equipment on the unit to meet its obligations. The unit
or components replaced under warranty become the property of SDMO Industries.
LIMITATION OF THE WARRANTY:
The warranty applies to units installed, used or maintained in accordance with the documentation provided by SDMO Industries,
and in the event of any operating defect with the unit, caused by a fault with the design, manufacture or material. SDMO Industries
does not guarantee the performance capabilities of the unit, or its operation or reliability if it is used for specific purposes. Under no
circumstances can SDMO Industries be held responsible for any consequential loss, whether or not arising out of material damage,
which includes but is not limited to the following: Any operating losses, costs or expenses resulting from unavailability of the unit,
etc. The warranty is limited to the cost related to the repair or replacement of the unit or one of its components, excluding
consumables. The warranty therefore covers the costs of parts and labour, excluding travel costs. The cost of transporting the unit
or one of its components to the workshops of SDMO INDUSTRIES or one of its approved agents shall be borne by the Customer;
the "return" transport costs shall be borne by SDMO Industries. However, in the event that the warranty does not apply, all transport
costs shall be borne by the Customer.
Make: Trade name:
HX 3000 C
KOHLER- HX 4000 C
SDMO
HX 6000 C
HX 7500 T C
COMMERCIAL WARRANTY
Type:
3499231800300
3499231800508
3499231800706
3499231801703
B. GUESTIN
Studies & Engineering Director
Serial numbers:
01-2016-00000000-000
> 52-2019-99999999-999
GUIPAVAS, on 01/03/17