Operating Elements And Connections; Monitor - Monacor Security DVT-440SET Mode D'emploi

All operating elements and connections de -
GB
scribed can be found on the fold-out page 3.
Contents
1

Operating Elements and Connections . 14

1.1 Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1.2 Remote controller . . . . . . . . . . . . . . . . . . . 15
1.3 Cameras . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1.4 Power supply units . . . . . . . . . . . . . . . . . . 15
1.5 Accessories . . . . . . . . . . . . . . . . . . . . . . . . 15
2 Safety Notes . . . . . . . . . . . . . . . . . . . . . . 16
3 Applications . . . . . . . . . . . . . . . . . . . . . . . 16
3.1 Conformity and approval . . . . . . . . . . . . . . 16
4 Setting into Operation . . . . . . . . . . . . . . 16
4.1 Installing the monitor . . . . . . . . . . . . . . . . . 16
4.2 Assigning cameras . . . . . . . . . . . . . . . . . . 17
4.3 Installing cameras . . . . . . . . . . . . . . . . . . . 17
5 Remote Controller . . . . . . . . . . . . . . . . . . 17
6 Basic Settings . . . . . . . . . . . . . . . . . . . . . 18
6.1 System settings . . . . . . . . . . . . . . . . . . . . . 18
6.2 Camera settings . . . . . . . . . . . . . . . . . . . . 18
7 Live Surveillance / Intercom Function . . 19
8 Photo and Video Recordings . . . . . . . . . . 20
8.1 Adjustments for the recordings . . . . . . . . . 20
8.2 Starting the recording . . . . . . . . . . . . . . . . 21
9 Viewing Photos and Video Recordings . 22
9.1 Live surveillance while replaying
a video recording . . . . . . . . . . . . . . . . . . . . 22
10 Deleting Recordings . . . . . . . . . . . . . . . . 23
11 Specifications . . . . . . . . . . . . . . . . . . . . . 23
14
1 Operating Elements
and Connections

1.1 Monitor

1 Antenna
2 SMA jack for the antenna
3 Signal output A / V OUT for connection of a
(larger) monitor
Press the button AV (8) so that a signal is pres-
ent at this output, then the screen (4) goes dark.
4 Screen
If one of the four camera pictures is shown, the
following symbols may be inserted:
a antenna symbol with indication of the signal
power of the camera signal
b display mode:
M = manual selection of a camera
S = scan mode (automatic switching of the
cameras)
c number of the camera channel shown
d symbol SD when a memory card has been
inserted
e symbol for the activated motion sensor: In
case a movement is detected, a video record-
ing starts or a photo is taken.
f symbol for the overwrite mode: If the memory
card is full, the oldest recordings are overwrit-
ten.
g clock symbol when a time-controlled record-
ing is programmed
h speaker symbol:
Red = the microphone signal of the camera
can be heard via the monitor speaker
Green = the button TALK (9) is being pressed
for talking; the microphone signal of the mon-
itor can be heard via the camera speaker
i indication X2 when the zoom function is
switched on (see chapters 6.2 and 7)
G
j Indication REC when a video recording is
made or symbol
5 Jack 12 V for power supply
Connect the larger power supply unit (26) to this
jack. Never connect one of the smaller camera
power supply units (25). It would be overloaded.
6 On / Off switch
7 Receiver for the remote control signals
when a photo is taken