General Safety - Altrad Belle VIBRATECH 38 Manuel De L'opérateur

GB
For your own personal protection and for the safety of those around you, please read and ensure you fully understand the following
safety information. It is the responsibility of the operator to ensure that he/she fully understands how to operate this equipment safely.
If you are unsure about the safe and correct use of the ''Vibratech'', consult your supervisor or Altrad Belle.
Improper maintenance can be hazardous. Read and Understand this section before you perform any
CAUTION
maintenance, service or repairs.
Work Area
KEEP your work area clean and well lit. Cluttered benches and dark areas invite accidents.
DO NOT OPERATE
Power tools create sparks wich may ignite the dust or fumes.
KEEP bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control.
Electrical Safety
EARTHED TOOLS MUST BE PLUGGED INTO an outlet properly installed and grounded in accordance with all codes and ordinances.
NEVER REMOVE the grounding prong or modify the plug in any away.
DO NOT USE any adaptor plugs.
CHECK
cally malfunction or break down, grounding provides a low resistance path to carry electricity away from the user.
AVOID body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of
electric shock if your body is grounded.
DON'T EXPOSE power tools to wet conditions. Water entering a power tool will increase the risk of electric shock.
DO NOT ABUSE the cable.
NEVER USE the cable to carry the tool.
NEVER PULL the plug from an outlet.
KEEP the cable away from heat, oil, sharp edges or moving parts.
REPLACE damaged cables immediately. Damaged cables increase the risk of electric shock.
WHEN OPERATING a power tool outside, use an outdoor extension cable marked "W-A" or "W". These cables are rated for
outdoor use and reduce the risk of electric shock.
Service
Tool service MUST BE PERFORMED
When servicing a tool, USE only identical replacement parts.
FOLLOW instructions in the Maintenance section of this manual.
Personal Safety
STAY ALERT, watch what you are doing and use common sense when operating a power tool.
DO NOT USE TOOL
power tools may result in serious personal injury.
DRESS PROPERLY.
AVOID accidental starting.
BE SURE
invites accidents.
REMOVE adjusting keys or spanners before turning the tool on. A spanner or a key that is left attached to a rotating part of the tool
may result in personal injury.
DO NOT overreach.
KEEP proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected
situations.
USE safety equipment.
Tool Use And Care
DO NOT FORCE the tool.
USE the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed.
DO NOT USE tool if switch does not turn it on or off. Any tool that cannot be controlled with the switch is dangerous and must be
repaired.
DISCONNECT the plug from the power source before making any adjustments, changing accessories, or storing the tool. Such
preventive safety measures reduce the risk of starting the tool accidentally.
STORE idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users.
CHECK for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tools
operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools.
USE only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool,
may become hazardous when used on another tool.
NEVER leave the Poker with the motor running. After operation and during work breaks deposit the Poker in a safe
manner. Make sure the Convertor can not roll away or fall down, especially whilst in transit.
NEVER use the electric cable of the Poker to pull the plug out of the socket.
Protect electric cables against heat, oil and sharp edges.
Avoid long running times when the machine is switched on and standing in the open air as well as touching solid objects over a
longer time period.
Do not pull out the plug from the socket by pulling on the cable.
Shield the electric cable from heat, oil and sharp edges.
Switch of the machine after use and store it carefully. Avoid dropping it and placing it down where it may roll away.

General Safety

8