Adjusting The Turning Handle; Holding The Hedge Trimmer When In Use - Okay HSD 700 Prof Manuel D'utilisation

5. Before use
Mounting the bow-type handle (Fig. 1)
The bow-type handle must be pulled over the blade sys-
tem from below as shown in Fig. 1 and then set into the
relief of the hedge shears housing. In doing so, one must
not push the two parts of the bow-type handle together.
To fix the bow-type handle the two included screws must
be screwed into the threadings in the housing through
the openings of the handle and fastened tightly.
Handguard (Fig. 2)
Slide the handguard onto the handguard plate at the
front side of the housing until it effectively locks into
place.
Power connection
The machine can only be connected to a single-phase
a.c. current connection. The machine is protectively
insulated in accordance with classification II of VDE
0740. Before using the machine ensure that the mains
current agrees with the operating voltage data on the
machine's identification plate.
Power Circuit Breaker:
Machines which will be used in different outside
locations must be connected to a Power Circuit
Breaker.
Securing the power supply cable (Fig. 3)
Only use cables (extension flex) that are approved for
outdoor use. The cable diameter must be equal to or big-
ger than 1.5mm² for cable lengths up to 75m.
Put the coupling of the extension flex onto the shears' plug.
For strain relief, stick a loop of the extension flex through
the opening in the handle and put it onto the strain relief
hook. After finishing work, slide the loop ahead over the
hook and pull it back through the handle opening. Pull
the mains plug.
Extension flexes with a length of more than 30m reduce
the machine's output.
6. Instructions for use of the equipment
Do not use the trimmer in rain or for cutting wet
hedges!
Check the hedge trimmer flex and its connections
before each and every use for visible signs of
damage (disconnect the power plug)! Do not use
a faulty flex.
Gloves:
Protective gloves must be worn when using the
hedge trimmer.
7. Switching the hedge shears on/off
When switching the hedge shears on take a safe stand.
These hedge shears have a two-hand safety switch. To
switch the hedge shears on the bar switch in the handle
(A) and the grip switch of the bow-type handle (B) must
be pushed down. To switch the device off let go of both
switches. The motor already stops if one of the two
switches is released.

8. Adjusting the turning handle

To facilitate your work the hedgetrimmer are equipped
with a turning rear handle that can be set in 3 different
positions (right, left, and normal). The purpose of this
mechanism is that especially for cutting in vertical direc-
tion the hedge shears can be held in their ergonomically
most favourable position whereby an early fatigue of the
user is avoided.
Please proceed as follows to change the position of the
handle:
Release switch (A). Pull back the locking pin (C) (Fig.
5). The handle is now unlocked and can be turned to the
desired position (Fig. 6+7). In the desired end position,
the pin locks back into place and securing the handle
and avoiding an accidental change of the position.
Please bear in mind that the locking pin (C) can only be
pulled back when the switch (A) is not activated (held
down). Make sure that the locking pin locks into place
again after repositioning the turning handle. Only then
the switch can be activated anew.
9. Maintenance
Always disconnect the plug from the power socket
before commencing any work on the machine.
Important: Always clean and oil the blades after pro-
longed use of the hedge trimmer. This will greatly affect
the life of the equipment. Damaged cutting units must
be properly repaired immediately. Clean the shearing
blades with a dry cloth or – in case of heavier dirt – with a
brush. Attention: Danger of injury!Oiling of the blades
should ideally be carried out using an environmentally
friendly lubricant (Fig. 8).
Sharpening of the blades
The blades generally do not need servicing and do
not require resharpening if used correctly. In order to
prevent injuries caused by the blades when not in use,
the sharpened cutting blade should be covered by the
blade cover (Fig. 9). The blades cannot be sharpened by
the user without opening the equipment and the safety
mechanism. Resharpening of the blades can therefore
only be carried out at a specialist workshop.
Changing the blades
Only correct installation of the blades will guarantee
problem-free operation and function of the above
mentioned safety feature of the blades. Changing of
the blades should therefore only be carried out at a
specialist workshop.

10. Holding the hedge trimmer when in use

(Fig. 10)
(Fig. 4)
This equipment will enable you to cut or trim bushes and
hedges easily and comfortably.
Trimming of hedges
- Young shoots are best cut in a scythe move ment.
- Older and stronger hedges are best cut in a sawing
movement.
GB-3