MIRKA CEROS Instructions D'utilisation page 93

Technical data
Mirka® CEROS
Power (peak/nominal)
Input voltage
DC voltage to sander
Speed
Orbit
Size of backing pad
Weight
Degree of protection (power)
Degree of protection (sander)
Noise and vibration information
Measured values are determined according to EN 60745 .
Mirka® CEROS
Sound pressure level (L )
pA
Sound power level (L )
WA
Sound measurement uncertainty K
Vibration emission value a
h
Vibration emission uncertainty K
Specifications subject to change without prior notice . Model range may vary between markets .
Troubleshooting guide
Symptom
No light from power supply LED when
switched on.
The LED on both power supply and
sander changes to red when sanding.
The sander LED is red and the sander
slows down to 4,000 rpm when sanding.
The sander LED is red and rpm
is slightly reduced.
Disposal information
DANGER!
Disposal guidelines for old appliances . Render redundant power tools unusable by removing the
power cord . Only for EU countries . Do not dispose of electric tools along with household waste .
According to European Directive 2002/95/EC, 2012/19/EU + 2003/108/EC on waste electrical and
electronic equipment and its implementation under national law, electric tools that have reached the
end of their life must be collected separately and taken to an environmentally compatible recycling
facility .
680CV 650CV
400 W / 350 W 400 W / 350 W
90–240 VAC 90–240 VAC
22 VDC 22 VDC
4,000–10,000 rpm 4,000–10,000 rpm 4,000–10,000 rpm 4,000–10,000 rpm 4,000–10,000 rpm
8 .0 mm 5 .0 mm
Ø 150 mm Ø 150 mm
0 .94 kg 0 .92 kg
I I
680CV 650CV
67 .8 dB(A) 67 .8 dB(A)
78 .8 dB(A) 78 .8 dB(A)
2 .0 dB 2 .0 dB
3 .75 m/s 2 .82 m/s
2
1 .5 m/s 1 .5 m/s
2
Possible Cause
Power cord not properly attached
to power supply unit or to the AC socket .
Broken fuse .
Too heavy long-term load .
Temperature too high in the sander .
Too heavy long-term load .
Too heavy short-term load .
625CV
400 W / 350 W
90–240 VAC
22 VDC
2 .5 mm
Ø 150 mm
0 .89 kg
I
625CV
67 .8 dB(A)
78 .8 dB(A)
2 .0 dB
2 .71 m/s
2 2
1 .5 m/s
2 2
Solution
Connect it properly .
Replace the fuse . One spare fuse
is included inside the fuse holder .
Use lighter load . Switch off the power .
Wait 5 seconds . Switch on again .
Reduce load on the sander for some time
and the sander will speed up again .
Use lighter load and the LED will
automatically change to green .
Mirka® CEROS • 150 mm (6") • 125 mm (5") • 77 mm (3")
550CV 325CV
400 W / 350 W 400 W / 350 W
90–240 VAC 90–240 VAC
22 VDC 22 VDC
5 .0 mm 2 .5 mm
Ø 125 mm Ø 77 mm
0 .87 kg 0 .70 kg
I I
550CV 325CV
67 .8 dB(A) 66 dB(A)
78 .8 dB(A) 77 dB(A)
2 .0 dB 2 .0 dB
2 .7 m/s 5 .2 m/s
2 2
1 .5 m/s 1 .5 m/s
2 2
en | us • ca
93