Güde GWS 700 HM-2 Traduction Du Mode D'emploi D'origine page 28

ENGLISH
24
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must
be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such pre-
ventive safety measures reduce the risk of starting
the power tool accidentally.
d) Store idle power tools out of the reach of child-
ren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
e) Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the po-
wer tool's operation. If damaged, have the pow-
er tool repaired before use. Many accidents are
caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed. Use of the power
tool for operations different from those intended
could result in a hazardous situation.
5) Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
Safety instructions for circular saws
for firewood
Operation is only allowed with a safety switch
against stray current (RCD max. stray current of
30mA).
The machine must be plugged to 400 V with 16
A fuse.
Wear ear protectors. Exposure to noise can cause
hearing loss.
Wear gloves when handling saw blades and rough
materials.
When being operated, the machine must stand on a
horizontal and flat surface and the floor around the
machine must be flat, well-maintained and with no
waste, such as sawdust and cuttings.
The processed bundle of workpieces and finished
workpieces should be placed near the standard place
of work of the operator.
Switch the machine off and unplug it when unatten-
ded.
Check all screw and plug-in connections and
protective equipment if firm and tightened
properly and whether all moving parts are
running smooth whenever the appliance is to be
put into operation.
The protective equipment on the appliance is
strictly prohibited to be disassembled, changed,
used in conflict with the designation and it is
prohibited to attach any protective equipment of
other manufacturers.
For cleaning and maintenance, the following
safety guards must be removed:: Additional safety
device for saw blade protection
After carrying out the work, all safety guards
must be reinstalled again correctly! See image
description.
The appliance must not be used if damaged
or safety equipment is defective. Replace any
worn-out and damaged parts.
Vor jedem Gebrauch Gerät , Anschlusskabel, Verlän-
gerungskabel und Stecker auf Beschädigung und
Alterung kontrollieren. Beschädigte Teile nur von
einem Fachmann reparieren lassen.
Any faults with the machine, including any related to
the safeguard or the saw blades, must be reported to
the persons in charge of safety as soon as the faults
are discovered.
Before pressing On/Off, make sure the saw blade has
been fitted properly.
The saw must not be used any longer if the cradle
fails to automatically return to the rest position.
The saw must not be used any longer if the saw
blade fails to stop in 10 seconds after switching the
machine off.
For security, use devices such as safety- and pressure
device, guide slide, rip fence, etc.
Removing sawdust and chippings from the machine
when running is strictly prohibited.
It is necessary to refrain from removing any cuttings
and parts of workpieces from the cutting area.
Do not use saw blades which are damaged or
deformed
Properly sharpened saw blades to be used only.
Follow instructions for use, adjustment and repair of
saw blades of manufacturers.
Do not use saw blades not corresponding to the key
data given in these instructions for use.
The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool.
Only use tools that meet standard EN 847-1.
Transport and store the tools in a suitable receptacle;
To minimise noise production, the tool must be
sharpened and all elements for noise minimisation
(covers, etc.) must be properly adjusted.
Replace the table insert when worn
Familiarise with the safety procedures for cleaning,