Operational.controls; Checking.the.running.direction - Becker S80 Notice D'utilisation

UP button
When.the.UP.button.is.pressed,.the.door.opens.in.self-locking..When.it.reaches.the.top.end.position.or.if.a.safety.function.actu-
ates,.the.door.stops.automatically..If.the.UP.button.is.pressed.while.the.door.is.closing,.the.door.movement.stops.immediately,.
and.moves.to.the.top.end.position.after.a.delay.time.of.0.5.s.(time.Z0).
STOP button
When.the.STOP.button.is.pressed,.the.door.stops.
DOWN button
When.the.DOWN.button.is.pressed,.the.door.closes.in.self-locking.if.a.sensitive.edge.is.used..If.no.sensitive.edge.is.connected,.
only.deadman's.mode.(tapping.mode).is.possible..If.the.sensitive.edge.or.light.barrier.actuates.the.door.stops.(sensitive.edge:.
stopping.time.Z2.=.0.3.s,.Light.barrier:.stopping.time.Z0.=.0.5.s).and,.depending.on.the.setting.(DIP.switch.1.3).moves.to.the.
top.end.position.or.clears.the.obstacle.(clearance.time.Z1.=.2.s).
EMERGENCY OFF Button (optional)
If.the.EMERGENCY.OFF.button.is.pressed,.the.drive.is.disconnected.from.the.mains.supply...The.door.is.brought.to.a.sustained.
halt.and.the.LED.+UB.lamp.goes.out..The.door.can.only.move.again.when.the.EMERGENCY.OFF.button.has.been.unlocked.
Main switch (optional)
The.system.is.disconnected.from.the.mains.using.the.main.switch.
Use.a.padlock.to.ensure.that.the.switched-off.main.switch.cannot.be.accidentally.switched.on.again.
Note
To check the running direction, you can fix the housing cover with just 2 screws so that it is laterally offset
on the housing. This will enable access to all operating and display elements.
The.direction.of.rotation.of.the.drive.depends.on.the.connection.of.
the.3.mains.phases.to.the.control,.and.must.be.checked.first.of.all..
Proceed.as.follows:
•. Move.the.door.into.the.half-open.position.by.hand.(e.g..with.the.
crank.handle).
•. Insert.the.CEE.plug.into.the.CEE.socket.or.switch.on.the.main.
switch.
•. Check.whether.the.control.is.in.deadman's.mode.by.checking.
whether. the. Stoer2. LED. is. illuminated. (ELS. Professional. Card.
3.1).. If. this. is. not. the. case,. press. the. Prog. programming. but-
ton.(approx..3.s).until.the.Betr.LED.changes.its.flashing.rhythm.
(flashes.1x)..You.are.now.in.setting.mode.(Step.1).and.the.door.
will.move.in.deadman's.mode.
•. Use. the. UP. and. DOWN. buttons. to. check. whether. the. running.
direction.of.the.door.agrees.with.the.buttons.pressed..Also.note.
the. OPEN. and. CLOSED. direction. indicator. LEDs. on. the. basic.
panel.of.the.S80.
If. the. running. direction. does. not. correspond. to. the. button. com-
mands,.proceed.as.follows:
•. Safely.disconnect.the.S80.control.from.the.mains.
•. Swap. two. phases. at. the. mains. connection. terminals,. e.g.. the.
cables.at.terminals.L1.and.L3.(see.position.of.the.terminals.and.
components.as.well.as.the.wiring.diagram).
•. Check.the.running.direction.again.
Operational controls
Checking the running direction
S80 with ELS Professional Card 3.1
DE
GB
FR
NL
29