Set-Up And Operation; Safety Features; Cleaning And Maintenance; Ce-Statement - EUROM EK5001 Manuel D'utilisation

Set-up and Operation

If the heater is being used for the first time (or if you want to reset the desired temperature), turn the thermostat dial to the maximum
position (clockwise as far as it goes).
With the mode selector dial, adjust the heater to suit your preferences: fan only, low power (EK15002: average power) or high power.
Once the temperature in the area being heated has reached the right level, slowly turn the thermostat dial anticlockwise until you hear a
soft click; leave the dial in that position. The heater will automatically maintain the temperature at this level. It does this by switching the
heating elements off and on when the temperature rises or falls too much.
If so desired, you can now switch to a lower power level.
To switch off, turn the power switches to O (off). The heater switches off. Unplug.
Note! After the thermostat has switched the heating elements off, the fan will keep turning. This means that the air is constantly moved,
allowing the heater to accurately detect if the area is cooling down.
The thermostat dial is continuously adjustable. A higher temperature is set by turning it clockwise; a lower temperature by turning it
anticlockwise.

Safety features

In case of internal overheating, the overheating safeguard will switch the heater off. If this occurs, immediately turn the mode selector
dial to O, unplug and allow heater to cool down for at least 10 minutes. The EK9002 and EK15002 require resetting now by inserting a pen
into the small reset hole on the operating panel. In theory, the heater can now be used as normal.
There is, however, generally a reason for an appliance overheating. This may be because the heater cannot adequately release its heat or
take in fresh air (because the heater is covered, the grills are blocked, the heater is placed too near a wall etcetera). Before using the
heater again, therefore, remove or adjust whatever caused the appliance to overheat. If you cannot find the cause and overheating recurs,
stop using the heater and contact your vendor or a certified electrician for inspection/repair. Overheating poses a serious fire risk!

Cleaning and Maintenance

Keep the heater clean. Deposits of dust and dirt in the appliance are a common cause of overheating so these should be removed
regularly. Switch off the heater, remove the plug from the socket and allow the heater to cool down before cleaning or carrying out
maintenance work..

Wipe the outside of the heater regularly with a dry or slightly damp cloth. Do not use aggressive soaps, sprays, cleaners or
abrasives, waxes, polishes or chemical solutions!

Use a vacuum cleaner or compressor to carefully remove any dust and dirt from the grills and ensure that the air intake and outlet
openings are clean. Be careful not to touch or damage any internal parts during cleaning!

The heater contains no other parts which need maintenance.

At the end of the season, store the cleaned heater in the original packaging if possible. Store upright in a cool, dry and dust-free
place.

Do not dispose of the heater with household waste when it becomes worn or damaged beyond repair. Take it to your local
authority's collection point for electrical appliances where any reusable materials will be collected and redistributed.

CE-statement

Euromac bv., Genemuiden-NL hereby declares that the EUROM workspace heaters, type EK5001 – EK9002 – EK15002, comply with
the LVD guideline 2006/95/EC and the EMC guideline 89/336/EEC and meet the following standards:
EN 60335-1:2002+A11,A1 :04+A12,A2 :06+A13 :08
EN 60335-2-30:2003+A1 :04+A2 :07
EN 62233 :2008
EN 55014-1:2006
EN 55014-2:1997/+A1 :2001
EN 61000-3-2:2006
EN 61000-3-3 :1995/+A1:2001/+A2 :2005
EN 61000-3-11 :2000
Genemuiden, 29-04-2011
W.J. Bakker, alg. dir.
13