Pentatech 3000 SET F4 Instructions D'installation page 44

20. Optional accessories
# 3000M, Door/window contact, Art.Nr.33531
# 3000R, Remote control, Art.Nr. 33532
# 3000P, PIR-detector, Art.Nr. 33530
# 3000 Set F3, wireless alarm system, Art.Nr. 33522
# 3000T, RFID tags (pack of 2), Art.Nr. 33535
# MK01, magnetic contacts (pack of 3), Art.Nr. 33103
# AS05, indoor siren, Art.Nr. 33133
# BL02, strobe, Art.Nr.33134
# RA300i/R, smoke alarm with relay output, Art.Nr. 10306
# GA90-230, Gasalarm 230 V AC, Art.Nr. 22152
21. Enrolling further wireless components
and RFID tags
! Enter the valid user code into the keypad of the panel (factory default 1234)
! Press the record key [8]. The key illuminates for 15 seconds. Within this
period enroll one of the following components as follows:
# Remote control: press the disarm button [34] once
# PIR-detector: press the test button [45] twice
# door/window contact: trigger by separating magnet from the sensor
# RFID tag: hold the tag in front of the RFID reader [3]
The enrollment is confirmed by one beep. A double beep means the
component is already enrolled. The first enrolled detector will be stored as
detector 1, the second as detector 2 etc. The detectors and the RFID tags in
the set are already enrolled.
22. Enrolling a wireless indoor siren
3000IS/3000IS2
It is possible to use the siren from the 3000 Set F2 or F3 as a wirless siren for
the 3000Z panel. The wireless range between these components is max 40m
(in free space).
! Delete all componenets from the 3000IS (see manual Set F2 or F3).
! Press the connection button of the 3000IS, its LED will illuminate.
! Press the arm key [4] on the panel keypad. The enrollment will be
confirmed by one beep of the 3000IS.
! Test the function by arming the panel. Both the panel and the siren
should confirm with one beep.
In alarm the 3000IS sounds. Its alarm period is factory set to 3 minutes and
this cannot be changed, irrespective of the alarm period set in the panel.
23. Deleting components and reset
Delete all wireless com ponents
! Remove the panel from the wall mounting bracket.
! Press the tamper bu tton [16] 3 times within 3 seconds. The deleting will
be confirmed by 2 beeps.
Reset
Remove the panel from the wall mounting bracket.
!
! Press the tamper button [16] 5 times within 3 seconds. The reset will be
confirmed by 2 beeps.
44
Alternatively send SMS command "0000"
24. Disposal
Packaging material, used batteries or electrical products must not be
disposed of as household waste. Use your recycling system. Details
are available from your local authority.
25. Simplified EU declaration of conformity
Hereby, INDEXA GmbH declares that the radio equipment type 3000 Set F4
is in compliance with Directive 2014/53/EU. The full text of the EU
declaration of conformity is available at the following internet address:
http://www.pentatech.de/de/downloads/cat_view/13-ce-
erklaerungen.html.
26. Legal Notices
This product or software may contain or make use of code under the GNU General
Public License v2 e.g. the linux kernel, the GNU Lesser General Public License v2.1
or the Apache licence v2.0.
For further information regarding license terms and – where required by license
– source codes please send an email to copyrequest@indexa.de to get them
free of charge. Some licenses, however, require the provision of physical copies of
the source code. In this case, you may obtain a copy of the source codes by
contacting us as well via copyrequest@indexa.de. A nominal fee (i.e., the cost of
physically performing the source distribution) will be charged for this service.
Note: your copy of this product may not contain code covered by one or more of
the licenses listed here, depending on the exact product and version you choose.
The corresponding license texts can be found at the end of the manual.