Wall Mounting - Pentatech 3000 SET F4 Instructions D'installation

10.1 ZONE jumper [59/65] (3000P , 3000M)
D0 D1 D2 D3 setting
{ {
Immediate
{ {
alarm
{ {
delayed alarm
{ {
{ {
Home mode
{ {
{
24 h
{
* If the delay in the panel is not activated (delay = 0 seconds) a delayed
detector will give an immediate alarm.
Factory default: delayed alarm
All functions are described in chapter 7.
10.2 LED jumper [58] (3000P)
OFF ON
{
LED active (LED indicates a detection and low
battery)
{
LED deactivated
factory default: LED on
11. Installation
11.1 Panel 3000Z
! Switch the power switch [19] to the OFF position.
! If required connect any optional wired accessories (see chapter 16)
! Switch the power switch to the ON position.
! Close the cover [28] so that the cable protrudes through the top middle.

! Wall mounting

! Mark the position for the screw holes through the screw holes [26]
onto the wall.
! Drill the fixing holes and insert the wall plugs [31].
! Fix the bracket to the wall with the screws [30].
! Hang the panel with the keyhole slots [17] over the bracket
Table use
! Hang the panel over the with the keyhole slots [17] onto the stand.
! Connect the mains adapter with the mains outlet.
When the panel is on the bracket or the stand the tamper switch [16] is
depressed. If the panel is moved when the stand is used it will not activate a
tamper alarm.
11.2 PIR-detector 3000P/30002
! Mark the fixing positions on the wall through the fixing holes [51] of the
bracket [50].
! Drill two holes and insert the wall plugs [55].
40
reaction
immediate alarm in full and
part arm
delayed alarm in full and part
arm*
immediate alarm by full arm,
no alarm in part arm
always alarm
! Fix the bracket with screws [54] to the wall.
! Press the ball joint [53] into the bracket.
! Slide the bracket into the slot [44] on the back of the detector.
! Position the detector such that it is vertical, not tilted, and with the
screwhole [48] on top.
11.3 Door/window contact 3000M
Remove the protective film from one side of the adhesive pads [63].
! Attach the pads to the middle of the rear housing of the magnet [62]
and sensor [59].
! Remove the foil from the other side of the pads.
! Fix the magnet vertically on the window/doorframe directly next to the
window/door edge. Attach the sensor so that the arrows are level,
leaving a maximum gap of 10mm in closed condition (see Fig. E and G).
The contact will not operate on the hinged side.
Note:
If the window frame is thick, attatch the magnet to the edge of the frame to
ensure a maximum gap of 10mm (see Fig. H).
12. Operation
The factory default language for SMS is German. Change to English as
follows:
1. Send an SMS with text "5" to the panel SIM card.
2. The panel answers with following SMS:
TEL:
1.
2.
3.
4.
5.
3. Using the function "Forward" (or "Edit" on older mobile phones) enter
into the SMS the required phone numbers (without any spaces) eg:
TEL:
1.012345678987653
2.
3.
4.
5.
4.Forward the edited SMS to the panel SIM card.
5.A c onfirmation SMS will be sent from the panel:
Alarm-Telefonnr.
erfolgreich gespeichert.
6. Send an SMS with the text "0001" to the SIM card of the panel.
7.The panel confirms with SMS:
Set English successfully.
Note:
# Pressing of keys on the panel [4-10] is confirmed by a beep sound.
# The arm status of the system is indicated by the illumination of the arm
key [4], similarly the part arm status by the part arm key [9] and the
diarmed status by the disarm key [10].