Pentatech 3000 SET F4 Instructions D'installation page 41

12.1 Recording and playing of voice memo on the panel
! Press the record key [8]. You now have 10 seconds recoding time
indicated by the illuminated key. The play key [3] now flashes to
indicate an unheard memo.
! To listen to the memo, press the play key, which then ceases to flash. You
can repeatably listen to the last memo by pressing the play button.
12.2 Automatic dialing of preset number from the panel
! Press the telephone key [5]. The panel calls the preset number and you
telephone through the inbuilt microphone [11] and speaker [20].
During the call the telephone key is illuminated.
! To quit the call, repress the telephone key.
The preset number is set using SMS 8 (see chapter 14)
12.3 Telephone call through the panel
! Key in the required number using the numeric keys [6] and then press
the telephone key [5]. The panel calls the number and then you can
telephone through the inbuilt microphone [11] and speaker [20].
During the call the telephone key is illuminated.
! To quit the call, repress the telephone key
12.4 Arm and disarm on the panel keypad
! Press the arm key [4] to arm the system. If a delay is set then you can
exit the dwelling during this period. During this period the panel beeps
each second, during the last 15 seconds it beeps twice per second.
! To part arm the system press the part arm key [9].
! To disarm the system key in the user code (factory default: 1 2 3 4)
followed by the disarm key [10].
12.5 Disarm using RFID tag
! The system can also be disarmed by holding an enrolled RFID tag in
front of the RFID reader [3].
12.6 Arm and disarm using the remote control
! To arm press the full arm button [38]. The panel confirms with one beep.
If a delay has been set the siren will beep every second and you have
time to leave the dwelling during the delay period without triggering
alarm. During the last 15 seconds of the delay period the panel beeps
twice per second.
! If you wish to arm without confirmation beeps then press the part arm
button [36] before pressing the full arm button.
! To part arm press the part arm button [36]. The panel confirms with one
beep. If a delay has been set the siren will beep every second and you
have time to leave the dwelling during the delay period without
triggering alarm. During the last 15 seconds of the delay period the
panel beeps twice per second.
! If you wish to part arm without confirmation beeps then press and hold
the part arm button [8] for 1 second and then press the part arm button.
! To disarm press the disarm button [34]. The panel confirms with two
beeps.
! If you wish to disarm without confirmation beeps then press the part arm
button [36] before pressing the disarm button.
12.7 Panic alarm from the remote control
! Press the panic button [35]. The siren will sound alarm for approx. 3
minutes.
! You can silence the alarm by pressing the disarm button [34].
12.8 Arm and disarm by telephone call
! To arm the system, call the number of the panel SIM card from one of the
stored telephone numbers (stored with SMS 5). Hang up after hearing
the first ringing tone. As confirmation of arming the panel calls the
number back an hang up immediately.
! To disarm the system, call the number of the panel SIM card from one of
the stored telephone numbers (stored with SMS 5). Hang up after only
after the panel hangs up.
12.9 Operation via SMS
! Send an SMS from one of the stored telephone numbers (stored with
SMS 5) to the number of the panel SIM card. The SMS commands can
also be sent using the Application (App see Side 1).
SMS-text command reaction of the panel
0 disarm
1 full arm
2 part arm
3 listen in
+ speak
33 listen in
4 record
voice memo beep record for up to 10 sec.
13. Alarm
13.1 Alarm triggered by a detector
# Upon detection, a detector will send an alarm signal to the siren.
# If the system is armed, the panel will give an acoustic warning for the set
alarm period (factory default 3 minutes). If the detector was set to
delay, then the alarm will be delayed accordingly.
# Each telephone number stored in SMS 6 will be sent an SMS.
# Then alle the telephone numbers stored in SMS 5 will be called (also if a
call is answered). If a call is answered the acoustic siren in the panel will
stop for several seconds so that the called party can listen in through the
panel microphone.
# The alarm is indicated visually on the panel through the flashing of the
numerical key [6] corresponding to the alarmed detector (0= panic
alarm, 1 to 9= detector 1-9). This indication is cancelled when the
system is disarmed.
! To stop the alarm disarm the system. If the system is disarmed using an
RFID tag the number stored with SMS 7 is sent an SMS.
If the alarm is not cancelled the system remains armed after the alarm period
Note that in operating mode a PIR-detector will be deactivated for 3-5
minutes after each detection) that means that the PIR only sends a
signal to the siren after it has not registered movement for a period of 3
to 5 minutes..
sends confirmation SMS
sends confirmation SMS
sends confirmation SMS
Panel calls back; Accept the call to listen
and to speak through the panel
Panel calls back, Accept the call to listen in
Panel calls back. Accept the call after the
41