Changing The Play Speed; Applying A Master Tempo; Setting Cue Points - Pioneer MEP-7000 Mode D'emploi

BASIC CONTROLLER OPERATIONS

CHANGING THE PLAY SPEED

 Tempo adjustment
Slide the TEMPO adjust slider forward or back.
When moved toward the front (+), the tempo becomes faster,
and when moved away from you toward the rear (–), the tempo
becomes slower.
• The amount (%) of tempo change is shown in the display.
• The tempo of the piece can be changed even while
maintaining the same musical pitch; see "APPLYING A
MASTER TEMPO".
 Pitch bend
Press the PITCH BEND (+) button to increase the playback
speed, and press the (–) button to slow the playback speed.
 Selecting a tempo adjust range
Press the TEMPO control range button.
Each time the button is pressed, the variable range of the
TEMPO adjust slider changes (±6 %/±10 %/±16 %/WIDE).
When set to a variable range of ±6 %, the tempo changes in
increments of 0.02 %. When set to ±10 % and ±16 %, the
tempo changes in increments of 0.05 %. When set to WIDE,
the tempo can be changed in increments of 0.5 %.
MEMO
• When playing MP3/AAC/WAV/AIFF files, the variable range is
±6 %/±10 %/±16 % only.
• The tempo range setting is preserved in memory even when
power is turned OFF.
• The variable range setting value is show in the display.
• In the case of a track on DJ software, the temp range will
depend on the software's specifications.

APPLYING A MASTER TEMPO

During playback, press the MASTER TEMPO button.
• The button indicator (MT) will light; when the TEMPO adjust
slider is used to adjust the speed (tempo), the pitch of the music
will remain unchanged.
• The sound quality will change due to the digital processing of
the audio.
36
En

SETTING CUE POINTS

By setting a cue point in memory, you can set the track to cue
standby instantly merely by pressing the CUE button.
 Manual cue
1 During playback, press the play/pause () button and
pause playback around the point you wish to set as cue
point.
2 Find the accurate cue point.
Set the cue point using the frame number.
The cue point can be set in one-frame units (75 frames = one
second).
Use the jog dial or SEARCH (, ) buttons to adjust the
frame position. Rotating the jog dial one rotation moves
playback 75 frames, while pressing SEARCH button once
moves the playback one-frame in the designated direction.
Set the cue point while listening to the playback audio.
Rotate the jog dial slowly and return the play to the point just
before the place you wish to begin playback (if the jog mode is
something other than SCRATCH, the cue point will be the
point immediately after the sound heard in audible pause).
3 Once the frame number or audible sound is at the desired
cue point, press the CUE button.
• The sound will be muted, and the CUE button indicator will
light, indicating successful setting of the cue point.
• When a new cue point is set in memory, any previously set
cue point will be cleared from memory.
 Real time cue
During playback, press the IN/CUE button at the point you
wish to mark as a cue point.
This point will be recorded as a new cue point.
 To confirm the cue point (cue point sampler)
After setting the cue point, press and hold the CUE button.
The sound at the cue point will be audible so long as the CUE
button is held depressed.
 To return to the cue point (back cue)
1 During playback, press the CUE button.
The unit will return to the set cue point and enter cue standby
mode.
2 Press the play/pause () button.
Playback will begin instantly from the cue point.
 To modify a cue point (cue point modification)
1 During playback, press the CUE button.
The unit will return to the set cue point and enter cue standby
mode.
Press one of the SEARCH (, ) buttons.
2
• The cue point will be moved in one-frame increments (the
cue point sound will move).
• The cue point can also be moved by pressing one of the
SEARCH (, ) buttons and then rotating the jog dial
(the cue point sound will move).
3 Press the CUE button.
The point at which the CUE button is pressed forms the newly
set cue point.