Specifications; Standard Equipment - RIDGID 535 Manual Chuck Mode D'emploi

535 Manual Chuck/535 Auto Chuck Threading Machines

Specifications*

Pipe Threading Capacity
Bolt Threading Capacity
LH Threads
Motor Type
Phase
Motor Power 2.3 (1.7) 0.5 (0.37)
HP (kW)
Volts V 115
Frequency Hz
Current Draw Amp 15
Operating Speed RPM 36
Rotary Type
REV/OFF/FOR
Controls
Front Chuck Speed Chuck with replaceable Rocker-Action Jaw Inserts
Rear Centering Device
Die Heads
Cutter
Reamer
Oil System
Weight
(unit with oil and a DH)
Overall Dimension
L × W × H
Sound Pressure (L )**
PA
Sound Power (L )**
PW
* Refer to your machine serial number plate for information on motor rating and control panel for information on your specific machine.
** Sound measurements are measured in accordance with a standardized test per Standard EN 62481-1.
- Sound emissions may vary due to your location and specific use of these tools.
- Daily exposure levels for sound need to be evaluated for each application and appropriate safety measures taken when needed. Evaluation of exposure levels
should consider the time a tool is switched off and not in use. This may significantly reduce the exposure level over the total working period.

Standard equipment

Refer to the RIDGID catalog for details on equipment
supplied with specific machine catalog numbers.
The Threading Machine serial number plate is located
on the back cover. The last 4 digits indicate the month and
year of the manufacture.
6
535 Manual Chuck Machines
Universal Motor
Single Phase
2.3 (1.7) 1.8/2.3 (1.35/1.7)
115 230
50/60
20 7.5
54 36
Rotary Type
REV/OFF/FOR
(2/0/1) (2/0/1)
Switch Switch
Cam Action, rotates with Chuck
Model 820, 1/8" – 2" Full Floating, Self-Centering Cutter
7 qt (6.6 l), with integrated Gerotor Model MJ Pump (Units prior to 1996 – Model A Oil Pump)
260 lbs. (118 kg)
(With Tools In Operating Position and Cutter Fully Closed)
1/8 to 2 inch (3 to 50 mm) Nominal Pipe Size
¼ to 2 inch (6 to 50 mm) Actual Stock Diameter
With Modifications
Induction Motor
3 Phase
1.5 (1.1)
400 220
50 60
3.5/5.1 4.4
35/70 16/46/58
Rotary Type
Rotary Type
1/0/2
2/1/0/1/2
Switch
Switch for
speed and
Shifter knob
direction
for speed
control (see
selection
Figure 19)
ON/OFF Foot Switch
See RIDGID Catalog for available Die Heads
Model 341, 1⁄8" – 2", 5-Fluted Reamer
350 lbs. 290 lbs.
(159 kg) (132 kg)
37" × 21" × 21" (940mm × 535mm × 535mm)
85 dB(A), K=3
91 dB(A), K=3
Figure 3 – Machine Serial Number
535 Automatic Chuck Machines
Universal Motor Induction Motor Induction Motor
Single Phase
2.3 (1.7) 2 (1.5)
110 230 120
50/60 60
15 7.5 18
36 16/46/58
Rotary Type
REV/OFF/FOR
(2/0/1)
Rotary Type
2/0/1 Switch
Switch Shifter
knob for
speed selection
Automatic with four reversible Forged Jaws
Automatic, Centering only
350 lbs. (159 kg)
999-998-086.09_REV. C
3 Phase
1.8/2.3 (1.35/1.7)
400
50
3.5/5.1
35/70
Rotary Type
2/1/0/1/2
Switch for speed
and direction
control
(see Figure 19)