Cleaning And Maintenance; Defects And Malfunctions - Tunturi F40 Upright Bike Manuel De L'utilisateur

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 35
English
-
Use Dial UP/ DOWN key to select SPORTY program
1~4 ( fig. - 14) and press MODE/ ENTER to confirm.
-
Use Dial UP/ DOWN key to set time, press MODE/
ENTER to confirm.
-
Press START/ STOP key to start workout
-
Use Dial UP/ DOWN key to adjust resistance level.
Load level is shown in LEVEL window ( fig. - 11)
Cardio mode.
-
Use Dial UP/ DOWN key to select workout
program, choose CARDIO mode and press mode
key to enter next setting entry for CARDIO mode
program.
-
Use Dial UP/ DOWN key to set age ( fig. - 15)
-
Use Dial UP/ DOWN key to select 55% ( fig. - 16),
75%, 90% or TAG (Target H.R. _ Default 100)
-
Use Dial UP/ DOWN key to set time, press MODE/
ENTER to confirm.
-
Press START/ STOP key to start workout
-
Use RESET, to go back to main menu.
Recovery
-
The RECOVERY key will only be valid if pulse is
detected.
-
TIME will show „0:60" (seconds) and counts down
to 0.
-
Computer will show F1 to F6 after the countdown
to test heart rate recovery status. User can find the
heart rate recovery level based on the chart below.
-
Press RECOVERY key again to return to the
beginning.
F1
Outstanding
F2
Excellent
F3
Good
F4
Fair
F5
Below average
F6
Poor
Body Fat
-
Press the BODY FAT key to start body fat
measurement.
-
During measuring, users have to hold both hands
on the hand grips. LCD display "-" "- -" "- - -" "- - -
-" for 8 seconds until computer finish measuring.
-
LCD will display BMI and FAT %.
Body fat mode error codes
-
*E-1
There is no heart rate signal input detected.
-
*E-4
Occurs when FAT% and BMI result is below 5 or
exceeds 50.
Trouble shooting:
-
When the display of LCD is dim, it means the
batteries need to be changed.
-
If there is no signal when you pedal, please check if
the cable is well connected.
NOTE
When stop training for 4 minutes, the main
screen will be off.
If the computer displays abnormally, please re-
install the transformer and try again.
APP
-
This console can connect APP on the smart device
by Bluetooth or Tunelinc.
-
Once console is connect to smart device via
Bluetooth or Tunelinc, the console will power off.
NOTE
Tunturi only provides the option to connect your fintess
console throughout a blue tooth connection. Therefore
Tunturi cannot be held resposible for damage, or
malfunctioning of products other than Tunturi products.

Cleaning and maintenance

The equipment does not require special maintenance.
The equipment does not require recalibration when
it is assembled, used and serviced according to the
instructions.
WARNING
Do not use solvents to clean the equipment.
Clean the equipment with a soft, absorbent cloth
after each use.
Regularly check that all screws and nuts
are tight.
If necessary, lubricate the joints.

Defects and malfunctions

Despite continuous quality control, defects and
malfunctions caused by individual parts can occur in the
equipment. In most cases, it will be sufficient to replace
the defective part.
-
If the equipment does not function properly,
immediately contact the dealer.
-
Provide the model number and the serial number of
the equipment to the dealer. State the nature of the
problem, conditions of use and purchase date.
2 2

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

F20

Table des Matières