Do Sa G E O F H A Za Rd O U S An D /O R T O X Ic Liq U Id S; Explosion Hazard; Sh Ip P In G T O T H E F Ac T O Ry F O R R Ep Ai R S An D /O R M Ain T E N An Ce; Intended Use Of The Pump - ETATRON D.S. eOne PLUS Notice D'installation, Mode D'emploi, Notice D'entretien

In the event of damage to the pump power cable, ask for it to be replaced by our service centres or qualified
•
personnel to prevent risks for the people who use it;
If you decide to no longer use an installed pump, it is recommended to disconnect it from the mains
•
This equipment is not explosion-proof. Do NOT install and do NOT use in an explosive or potentially explosive
•
environment.
Dosage of hazardous and/or toxic liquids
To avoid damage to persons or property arising from contact with hazardous liquids or toxic fumes, in addition to
compliance with the instructions contained in this booklet, the following standards should be made well aware of:
Always wear protective clothing, including gloves and safety goggles, operating as recommended by the
•
manufacturer of the liquid (additive) to be used. (Risk of potential explosions, burns, fire, personal injury or
damage)
Check that the hydraulic part of the pump is not damaged or broken and use the pump only when in perfect
•
condition.
Use tubes suitable for the liquid and the operating conditions of the plant, inserting them possibly inside PVC
•
protection tubes.
Before you turn off the metering pump you must depressurise the system and neutralise the hydraulic part
•
with a suitable reagent.
When you connect a metering pump either to the public water supply or to your own water source, you must
•
comply with the protection regulations in force or dictated specifically by the network provider. In both cases
always provide safety devices that prevent the return of flows towards the source, like for example check
valves etc.
WARNING: Protect the pump and chemicals from the elements (frost, rain, sun etc.).
•
It is recommended to install the pump in areas where leakage of liquid product (additive) cannot cause
•
personal injury or property damage.

Intended use of the pump

The pump is designed exclusively for the purpose for which it was expressly built, i.e. for metering liquids. Any other
use must be considered dangerous. Using the pump for applications other than those for which it was designed is
prohibited. For further details, customers may contact our offices to receive information about the type of pump
purchased and its proper use. The manufacturer cannot be held responsible for any damage caused by improper,
erroneous or irrational use.
Shipping to the factory for repairs and/or maintenance
The material to be sent to the factory for maintenance should be disassembled and packed carefully; all the parts in
contact with the chemical must be emptied and rinsed to ensure the safety of the operators while transporting and
handling the material in the laboratory. In the event of failure to comply with the instructions given, we reserve the right to
reject the equipment and to return it at your expense; damage caused by the chemical to the material will be included in
the repair estimate.

Assembly and Disassembly

All Etatron DS dosing pumps are usually supplied already assembled. For greater clarity, you can consult the
attachment at the bottom of the manual which illustrates an enlarged view of the pump, and all the details with its
nomenclature, so that you can have a complete picture of the pump components. These drawings are however
indispensable if you have to identify malfunctioning or defective parts. Other designs, related to the hydraulic parts (pump
head and valves) are shown for the same purpose, in the appendix.
For the eventual dismantling of the pump or before starting work on it:
Make sure that it is turned off electrically (both polarities) by disconnecting the connection cables from the
•
contact points of the network through the opening of a phase switch with a minimum contact gap of 3 mm
(Fig. 6).
In an appropriate manner, carefully dispose of any remaining pressure from the pump body and from the
•
injection tube.
Remove all liquid present from the pump body, then proceed by disassembling and reassembling the
•
pump body, by unscrewing and screwing the four screws (tightening torque: 180 to 200 N * cm).
This last point requires special attention, so please refer to the drawings in Annex 1 and the chapter "RISKS" before
starting any operation.

EXPLOSION HAZARD:

ENGLISH
51