Scheppach DP16SL Traduction Des Instructions D'origine page 29

b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of elec-
tric shock if your body is earthed.
c) Do not expose power tools to rain or wet con-
ditions. Water entering a power tool will increase
the risk of electric shock.
d) Do not use the cable for another purpose, for
example, carrying or hanging the power tool
or pulling the plug out of the socket. Keep the
cable away from heat, oil, sharp edges or moving
device parts. Damaged or coiled cables increase
the risk of an electric shock.
e) If you work with a power tool outdoors, only
use extension cables that are also suitable for
outdoor use. Using an extension cable suitable
for outdoor use reduces the risk of an electric
shock.
f) If you cannot avoid using the electrical tool in
a wet environment, use a fault-current circuit
breaker. Use of an RCD reduces the risk of electric
shock.
Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or med-
ication. A moment of carelessness when using
electrical tools can result in serious injuries.
b) Use personal protective equipment. Always
wear eye protection. Protective equipment such
as a dust mask, non-skid safety shoes, hard hat or
hearing protection used for appropriate conditions
will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools
that have the switch on invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on. A tool or spanner that
is located in a rotating device part may result in
injuries.
e) Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
g) If dust extraction and collection devices can
be mounted, make sure that they are connect-
ed and used properly. Use of dust collection can
reduce dust-related hazards.
h) Do not let familiarity gained from frequent use
of tools allow you to become complacent and ig-
nore tool safety principles. A careless action can
cause severe injury within a fraction of a second.
Power tool use and care
a) Do not overload the device. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
b) Do not use the power tool if the switch does
not turn it on and off. Any power tool that can-
not be controlled with the switch is dangerous
and must be repaired.
c) Disconnect the plug from the power source
and/or remove the battery pack, if detachable,
from the power tool before making any adjust-
ments, changing accessories, or storing pow-
er tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
e) Maintain power tools and accessories. Check
whether moving parts function properly and do
not get stuck and whether parts are broken or are
damaged and thus adversely affect the electric
tool function. If damaged, have the power tool re-
paired before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and the
work to be performed. Use of the power tool for op-
erations different from those intended could result
in a hazardous situation.
www.scheppach.com GB | 29