Publicité
GB
forces must be absorbed by the awning and trans-
ferred to the mounting plane via the fixing brack-
ets. Before first use, make sure that all screws are
firmly tightened.
• Extreme loads may exert great stress on the fixing
screws. Therefore, please ensure that the instal-
lation surface has sufficient capacity for these
loads. Consult a professional if you are unsure.
• Safe and risk-free use of the awning can be guar-
anteed only if the awning is checked and main-
tained on a regular basis. Inspect the awning reg-
ularly for signs of wear or damage to its covering
material or frame.
• In order to avoid damages, do not extend the
awning when there are strong winds.
• Contact your local vendor.
• Only use original spare parts. Only these replace-
ment parts are designed and suitable for the
device. Other replacement parts will not only lead
to an invalidation of the warranty, they may also
endanger you and your environment.
• Children or any other persons, who are not in a
position to operate the product safely and care-
fully due to insufficient physical, psychic or sen-
sory conditions, are not allowed to use or mount
the product.
• Store the radio remote controls out of the reach of
children. Do not permit children to play with the
control unit of the awning.
• Make sure you always wear the required personal
protective clothing.
• Exercise caution and only work when in a good
condition: If you are tired, ill, if you have ingested
alcohol, medication or illegal drugs, do not use the
product as you are not in a condition to use it
safely.
Qualification
Installation by specialists only
Can only be installed by a qualified electri-
cian.
• The installation instructions are designed for use
by a qualified technician who has thorough knowl-
edge of the following areas:
– Occupational safety, operational safety and
accident prevention regulations
– Working with ladders and scaffolding
– Handling and transport of long, heavy compo-
nents
– Working with tools and machines
– Installation of fixing materials
– Evaluation of building structure (If you have any
questions, consult your dealer.)
– Initial commissioning and operation of the prod-
uct
• If one of this qualifications are not available, then
an installation company with expertise in this field
should be commissioned to carry out the work.
30
Electrical connection
• The fixed electrical installation must be carried out
in accordance with VDE 100 by an authorised
electrical specialist.
• The awning may only be connection if the specifi-
cations on the awning identification plate match
those of the power source.
• The enclosed installation instructions for the sup-
plied electrical components must be observed.
Battery
• When inserting the batteries, make sure that the
polarity is correct (Plus/+ and Minus/-)
• Leaking or damaged batteries can cause irritation
in case of contact with the skin. Therefore, in such
cases, use suitable protective gloves to dispose
of the batteries.
• Make sure that batteries are not short-circuited,
disassembled, or thrown in to the fire. There is a
risk of explosion!
• Do not leave batteries out, there is a risk that
these may be swallowed by children or pets. In
the event of swallowing, consult a doctor immedi-
ately.
Manual operation (in the event of power failure)
• In the event of a power failure, the awning can be
operated using a hand crank.
• The operating element for the hand crank must be
accessible at a height of less than 1.8 metres.
• Be careful when extending the awning as, in the
event of weak or defective springs, it may fall
quickly.
Lifting with ropes
• If the awning must be raised to a higher area with
the help of ropes, then the awning
– should be removed from the packing,
– and connected with the ropes in such a way that
the ropes do not slip
– out and should be lifted whilst maintaining a
horizontal position.
Mounting brackets
• Before starting the assembly the following should
be checked,
– whether the mounting brackets supplied match
the scope of delivery in type and number,
– and if the specifications about the installation
surface made at the time of ordering the prod-
uct actually match the existing installation sur-
face.
• If any deviations are identified here which may
affect the safety, then the product should not be
installed.
Fixing materials
• The awning fulfils the wind resistance class as
specified in the technical specifications (► Tech-
nical data – p. 35).
• In the assembled condition it satisfied these
requirement only, if
– the awning is assembled with the type and
number of brackets specified in these instruc-
tions,
– the awning is installed whilst taking the speci-
fied plug extraction force into consideration
Publicité
