Publicité
res 10Min.) at the end of this time it switches to next phase.
GB
• If the cycle is temperature cycle for the second phase -
This value is used only if there is a core probe; this is the
maximum duration of the second phase if the temperature
defined in parameter iS2 is not reached.
13. Set point of the storage phase.
Cleaning & maintenance
• ATTENTION! Always disconnect the appliance from the power
supply and cool down before storage, cleaning & maintenance.
• Do not use water jet or steam cleaner for cleaning and do not
push the appliance under the water as the parts will get wet
and electric shock might be resulted.
• If the appliance is not kept in a good state of cleanliness, this
can adversely affect the life of the appliance and result in a
dangerous situation.
• Food residues should be regularly cleaned and removed from
the appliance. If the appliance is not cleaned properly, it will
reduce its lifespan and may result in a dangerous condition
during use.
• Before cleaning chamber perform a defrost cycle.
Cleaning
• Clean the cooled exterior surface with a cloth or sponge slight-
ly dampened with a mild soap solution.
• For reasons of hygiene, the appliance should be cleaned before
and after use.
• Avoid water contacting the electrical components.
• Never immerse the appliance in water or other liquids.
• Never use aggressive cleaning agents, abrasive sponges, or
cleaning agents containing chlorine. Do not use steel wool,
metallic utensils, or any sharp or pointed objects for cleaning.
Do not use petrol or solvents!
• Clean the door seal with water only.
• Clean needle probe at least one time per day.It is recommend-
ed to rinse probe with clean water and sanitizing solution.
• Periodically clean the condenser (followed only by qualified
technicians) using suitable tools (see fig. 8 on page 6)
Maintenance
• Check the operation of the appliance regularly to prevent se-
rious accidents.
• If you see that the appliance is not working properly or that
there is a problem, stop using it, switch it off and contact the
supplier.
• All maintenance, installation and repair work must be carried
out by specialised and authorised technicians, or recommend-
ed by the manufacturer.
Transportation and Storage
• Before storage, always make sure that the appliance has been
disconnected from the power supply and completely cooled down.
• Empty refrigerating chamber and clean it before storage the appli-
ance. Store the appliance in a cool, clean and dry place.
• Never place heavy objects on the appliance as this could damage it.
• Do not move the appliance while it is under operation. Disconnect
the appliance from power supply when moving and hold it at the
bottom.
• Special care must be taken when moving or transporting the ma-
chine due to its heavy weight. With at least 2 persons or using a
cart. Move the machine slowly, carefully, and never incline more
than 45°.
14
Troubleshooting
If the appliance does not function properly, please check the
below table for the solution. If you are still unable to solve the
problem, please contact the supplier/service provider.
Problem
Possible cause
Appliance is turn off.
The
Plug and/or cord are
appliance
damaged.
is not
working.
Fuse blown.
No power supply.
There is too much ice on
the evaporator.
Condenser is blocked
with dust.
Doors are not close
properly.
The
The appliance is located too
appliance
close to a heat source or
turns on,
the air flow to the condens-
but the
er is being interrupted.
tempera-
ture is too
Ambient temperature is
high/too
too high.
low.
Unsuitable food products
are being stored inside the
appliance.
The appliance is over-
loaded.
The ap-
Loose nut/screw.
pliance is
unusually
The appliance is not
loud.
installed on a level, stable
surface / is not properly
leveled.
The drain outlet is blocked.
Leaking
water
Movement of water to the
from
drain is obstructed
appliance
Water container is
damaged.
The drip tray is overflowing. Empty the drip tray.
Alarms / Error codes
If any alarm will be exist, error code and alarm icon
displayed on the control panel; also acoustic alarm will be ac-
tivated. To turn off acoustic alarm press any button on control
panel. To reset alarm manually, press and hold SETTING button
for 5 seconds. To solve problem chceck table below:
Error
Possible cause
rPf
Chamber probe failure.
2nf
Core probe failure.
Alarm of maximum
AH
temperature.
Possible solution
Check plug connection and
if the appliance is turn on.
Contact the supplier.
Contact the supplier.
Check power supply.
Start defrost cycle.
Contact the supplier.
Check if the doors are close
correctly and if the seals are
damaged.
Move the appliance to a
more suitable location
Increase ventilation or move
the appliance to a more
suitable location.
Remove food products that
are too hot for storage or are
blocking the fan inside the
appliance.
Reduce the amount of
food products stored in the
appliance.
Check and tighten all loose
nuts/screws.
Check the installation
position and/or adjust feet to
level appliance.
Clear drain outlet.
Clear bottom of the
chamber.
Contact the supplier.
will be
Possible solution
Probe connection are loose or not
working, check thermostat connec-
tion. Compressor output according
to parameters "Con" and "Cof".
Probe connection are loose or
not working, check thermostat
connection.
Outputs unchanged (manual reset).
Publicité
