Publicité
order to avoid a hazard.
• No other appliances should be plugged into the same socket
as with this appliance.
• WARNING! When positioning the appliance, ensure the supply
cord is not trapped or damaged.
• WARNING! Do not locate multiple portabel socket-outlets or
portable power supplies at the rear of the applaince.
Intended use
• This appliance is intended to be used for commercial use.
• The appliance is designed for quick chilling/freezing food for
commercial purposes. Any other use may lead to damage to
the appliance or personal injury.
• Operating the appliance for any other purpose shall be
deemed a misuse of the device. The user shall be solely liable
for improper use of the device.
Grounding installation
This appliance is classified as protection class I and must be
connected to a protective ground. Grounding reduces the risk of
electric shock by providing an escape wire for the electric cur-
rent.
This appliance is fitted with a power cord with grounding plug
or electrical connections with grounding wire. The connections
must be properly installed and grounded.
Control panel
(Fig. 1 on page 3)
1. Digital display
2. Arrow UP / Defrost cycle
3. Arrow DOWN / Time-based cycle
4. Chilling cycle / Freezing cycle
5. Button for intensive cycle mode ("HARD")
6. SETTING button
7. START / STOP button; Stand-by mode
8. Cycle for ICE CREAM
9. Cycle "FROST BUST" (-40°C)
List of LED icons
Icon
Description
Lighted up - defrosting cycle is in progress.
CH
Lighted up - chilling cycle is in progres; If flashing - cycle is
selected.
FR
Lighted up - freezing cycle is in progres; If flashing - cycle is
selected.
HD
Lighted up - Intensive chilling/freezing mode is in progress.
Lighted up - temperature-based cycle is in progres; If flashing
- cycle is selected.
Lighted up - appliance is in stand-by mode.
Lighted up - time-based cycle is in progres; If flashing - cycle
is selected.
Lighted up - "Frost bust" cycle (-40°C) is in progres; If flashing
- storage cycle is in progress.
Lighted up - cycle for ice cream is in progres; If flashing -
CH+FR
cycle is selected.
+
Lighted up - compressor and fan are working
Lighted up - alarm activated. Check => Troubleshooting.
Scheme of thermostat connection
(Fig. 2 on page 3)
Preparation before use
• Remove all protective packaging and wrapping.
• Check that the device is in good condition and with all accesso-
ries. In case of incomplete or damaged delivery, please contact
the supplier immediately. In this case, do not use the device.
• Clean the accessories and the appliance before use (See ==>
Cleaning & Maintenance).
• Make sure the appliance is completely dry.
• Place the appliance on a horizontal, stable and heat resistant
surface that is safe against water splashes and direct sunlight.
• Keep the packaging if you intend to store your appliance in the
future.
• Keep the user manual for future reference.
NOTE! Due to manufacturing residues, the appliance may emit a
light odor during the first few uses. This is normal and does not
indicate any defect or hazard. Make sure the appliance is well
ventilated.
Replacing feets into wheels (included)
(Fig. 4 on page 4)
• Two wheels with braeks should be installed at the front of ap-
pliance.
• Unplug appliance from main socket and secure the fork lift be-
fore change
• Secure all shalves and door and empty off chamber before
change.
• Lock the break on wheels after change.
Assembling water drip tray
(Fig. 5 on page 4)
NOTE: Assembling kit include only screws and rails. Kit not in-
clude GN 1/1 tray.
Changing side of opening the door
(Fig. 6 on page 5)
Operating instructions
ATTENTION: DO NOT put into chamber food products taken di-
rectly form the oven. Let them cool down a while.
General instructions
• When the appliance is connected to supply, the appliance is in
"Stand-by" mode; the icon
• To turn on the appliance: press the START/STOP button
icon
will light off. Current chamber temperature will by dis-
pleyed on the control panel.
• To lock keyboard on control panel: press and hold simultane-
ously arrow UP and arrow DOWN for 3 seconds - code "PoF"
will be displayed. To unlock keyboard - press and hold simulta-
neously arrow UP and arrow DOWN for 3 seconds once again
until code "Pon" will be displayed on the control panel.
• When corresponding buttons is press temperature cycle is
choosen as a default. To switch from temperature cycle to
timed cycle: after choose desire temperature cycle, press and
hold arrow DOWN for 3 second; clock icon
ing with corresponding icon to choosen cycle.
• To change setpoint of the temperature (+/- 1°C) or time (+/- 1
min.), depending on selected cycle, press arrow UP or arrow
DOWN after selecting cycle but before starting the cycle; cur-
rent value will be displayed on control panel and icon
°C+CH+
perature cycle) or icons
will light up.
will start flash-
°C
(tem-
(timed cycle) will start
11
GB
;
Publicité
