Publicité
Feature Guide
A. MAIN POWER SWITCH: Located at the back of the machine,
applies power to the laminator. The 'ON' position is indicated by
the 'I' symbol. The 'OFF' position marked 'O' symbol (figure 2).
B. CONTROL PANEL:
a. FOOTAGE COUNTER – Tracks the number of feet used since
last reset. To reset the footage counter press the RESET
button.
b. ON/OFF BUTTON – Used to put the machine in Standby
mode or wake the machine up from Standby mode.
i. READY – Machine is ready to use when machine beeps
and the ✓ icon LED turns GREEN.
ii. WARM-UP – Machine is warming up when the
is AMBER.
iii. STANDBY – When
is in Standby mode. Press the ON/OFF button to wake the
machine and warm-up to operational temperature.
c. FILM SELECTION – (38mic/75mic) – Press the film selection
button to toggle between 38mic and 75mic films.
i. To Change between NAP I and NAP II film (machine
comes defaulted to NAP II) – Press and hold the film
selection button for 10 seconds until the orange LED to
the right of the thickness indicators lights up, this indicates
NAP I has been selected.
d. SPEED CONTROL – Controls the speed of the laminator
when the run button is pushed.
i. AUTOSPEED – Machine runs at optimum speed for the
film type selected. PUSH the speed dial to turn this feature
ON/OFF. GREEN LED will illuminate when ON.
ii. MANUAL SETTINGS 1 THRU 10 – Operator can
manually select the speed 1 – 10. The speed will increase
as you adjust from 1 to 10. AUTOSPEED must be turned
OFF to manually adjust speeds.
e. RUN – Push the RUN button to run the laminator in the
forward direction.
f. SLOW FORWARD/REVERSE – Press and Hold to run the
machine slowly in Forward or Reverse. Using SLOW Speed
will allow the machine to run even when Heat Shield is open.
g. STOP – Used to Stop the laminator. There are two stop
buttons, one on front panel and one on back of the machine.
6
icon LED
6
icon is illuminated AMBER, machine
C. HEAT SHIELD: (figure 4) Prevents inadvertent contact with the
heat rollers. The HEAT SHIELD must be lowered for the RUN
operation to work.
D. FEED TABLE: (figure 4) The Feed Table is used to position
items for lamination. Feed table must be closed and latched for
laminator to operate.
E. FEED TABLE LATCHES: (figure 5) Used to unlock and lock the
FEED TABLE.
F. FEED TABLE GUIDE: (figure 5) Aligns items as they are being
fed into the laminator. Especially helpful on longer items to
reduce skew. The guide can be moved by loosening the knob and
sliding the guide to the desired position and then tightening the
knob.
G. HEATED NIP ROLLERS: (figure 6) Heats the film to activate the
adhesive and provides pressure to ensure film adheres to the
media.
H. I DLER BARS: (figure 6) The Idler Bars, located near each supply
roll, are used to direct the film to the NIP ROLLERS. The lower
Idler Bar is attached to the Feed Table to facilitate easy film
loading.
I. PULL ROLLERS: The Pull Rollers are located at the back of the
laminator. They simultaneously pull the film through the laminator
and provide tension as the film cools to ensure quality lamination.
J. REAR SLITTER: (figure 7) Used to cut the film when it exits the
rear of the laminator.
K. FUSE: (figure 2) the Fuse is an electrical safety device, located
under the main power switch.
L. AUTO SHUT-OFF: After two hours of activity the laminator will
shut down. To activate the laminator, ensure the Main Power
button is in the ON position ('I') and press the ON/OFF button on
the front of the machine.
M. FILM ROLL SUPPLY: The Ultima 65 can use both EZ Load and
Standard roll laminating film (figure 8).
N. FILM SADDLES: Film supply is loaded into the saddles (figure
9).
O. FILM SHAFT: The Film Shaft is used for loading standard film
onto the Ultima 65 Laminator.
P. FILM SHAFT HOOKS: Located on the back of the machine, the
shaft hooks are used to store the Film Shaft when EZ load film is
being used.
Publicité
