Publicité
General Safeguards
• Use this laminator only for its intended purposes as according to
the specifications outlined in the operating instructions.
• Keep hands, long hair, loose clothing and articles such as
necklaces or ties away from the front of the rollers to avoid
entanglement and entrapment.
• Avoid contact with the rollers during operation or shortly after the
laminator has been turned off. The rollers can reach temperatures
in excess of 150°C.
• Keep hands and fingers away from the path of the sharp film cutter
blade located at the film exit.
• Do not place the laminator on an unstable cart, stand or table. An
unstable surface may cause the laminator to fall resulting in serious
bodily injury. Avoid quick stops, excessive force and uneven floor
surfaces when moving the laminator on a cart or stand.
• Do not defeat or remove electrical and mechanical safety
equipment such as interlocks, shields and guards.
• Do not insert objects unsuitable for lamination.
• Do not expose the laminator to liquids.
Electrical Safeguards
• This laminator must be connected to a supply voltage
corresponding to the electrical rating as indicated on the serial
plate located on the rear of the machine.
• Unplug the laminator before moving it, or when it is not in use for an
extended period of time.
• Do not operate the laminator with a damaged power supply cord
or plug.
• Do not overload electrical outlets as this can result in fire or shock.
• Do not alter the attachment plug. this plug is configured for the
appropriate electrical supply.
• The unit is intended for indoor use only.
m
CAUTION: The receptacle must be located near the
equipment and be easily accessible. Do not use an extension
cord.
• Disconnect the attachment plug from the receptacle to which it is
connected and keep the power supply cord in your possession
while moving the laminator.
• Do not operate the laminator with a damaged power supply cord
or attachment plug, upon occurrence of a malfunction, or after
laminator has been damaged. Contact an authorized GBC service
representative for assistance.
Service
m
WARNING: Do not attempt to service or repair the laminator.
Failure to observe this warning could result in severe
personal injury or death.
Disconnect the plug from the receptacle and contact GBC Technical
Service when one or more of the following has occurred.
• The power supply cord or attachment plug is damaged.
• Liquid has been spilled into the laminator.
• The laminator is malfunctioning after being mishandled.
• The laminator does not operate as described in these instructions.
Installation
• Shipping damage should be brought to the immediate attention of
the delivering carrier.
• Place the laminator on a stable flat surface capable of supporting
68kg.
• The surface should be at least 76cm high to assure comfortable
positioning during operation. All four rubber feet should be on the
supporting surface.
• Connect power cord to an appropriate power source. Avoid
connecting other equipment to the same branch circuit to which the
laminator is connected as this may cause nuisance tripping of the
circuit breaker or blown fuses.
• The laminator should be postioned to allow exiting film to drop
freely to the floor. Accumulation of laminate as it exits the laminator
may cause film to wrap around the rollers, causing a jammed
condition.
• Avoid placing laminator near sources of heat or cold. Avoid locating
the laminator in the direct path of forced, heated or cooled air.
Caring for Ultima 65
The only maintenance required by the operator is to periodically
clean the rollers. Keeping the rollers clean ensures that your finished
items will not be damaged by dirt and adhesive build-ups.
m
CAUTION: The following procedure is performed while the
laminator is hot. Use extreme care.
m
WARNING: Do not apply cleaning fluids or solvents to the
rollers.
m
WARNING: Do not attempt to laminate adhesives marked
'Flammable'.
m
WARNING: Do not expose laminator to liquids.
1. Remove the film from the laminator following the procedure
outlined in the section FILM LOADING AND THREADING.
2. Clean the top and bottom rollers with a clean, damp lint-free
cloth. If there are any adhesive build-ups, you may use isopropyl
alcohol instead of water.
3. To remove difficult debris, Preheat the laminator until the READY
LAMP (✓) illuminates.
4. Push and hold the SLOW Backward button to rotate the upper
and lower rollers with the safety shield open.
5. Follow the procedure in section FILM LOADING AND
THREADING, Method using Film Threading Card to reload the
laminator.
Note: Do not use metal scouring pads to clean the heat rollers!
Note: Covering machine when not in use will reduce dust build-up
on the rollers and film which can lead to poor lamination quality.
m
WARNING: Do not laminate glitter and/or metallic items.
Damage to the rollers may result.
The side covers and feed table can be cleaned with a lint-free cloth
and a mild detergent.
G
5
Publicité
