Automatic Displayed Messages; Manual Regeneration; Salt Alarm Acknowledgement; Power Cut - BWT Aqapearl A6X Notice Originale

AUTOMATIC DISPLAYED MESSAGES

The displays shows:
Πan upper information line
 a lower information line
Ž a bargraph with 10 segments, showing the
remaining autonomy of the softener before the
next regeneration, by steps of 10%. The graph
in this example shows 70% remaining autonomy
For each operation step of the device, the dis-
played messages are as follows:
Ž


MANUAL REGENERATION

At any time, it is possible to trigger the rege-
neration of the softener, via the long press (5
seconds) on the OK key.
If this is done for a test purpose, it is possible to
manually go from one step to the next by briefly
pressing the OK key.

SALT ALARM ACKNOWLEDGEMENT

When no salt is left in the tank, the device
displays the alternate words SALT and CHECK.
Once the salt refill is done, you may just wait for
the next regeneration to let this alarm disappear.
It is recommended though to acknowledge
immediately the alarm, following these steps:
• Proceed with a long press (5 seconds) on the
M key
• Then briefly press this M key to go through
Accessed by the code 23, then the browsing works in the same way as the regular setting mode. The intervention on the advanced setting shall be
done by a trained professional. Any mistake can disturb the work of the device and is under its author's responsibility.
Step n° Display
PASSW ?
0
00
PROP R
1
On
CAPA
2
80
CONSU
3
71
SALT
4
2000
VOL OK
5
8 56
PEAKFL
6
10 68
N REGE
7
48
CHLOR
8
Off
ALARME
9
Off
SERV Alternate
12:30 with
REMPL
375
SAUM
180
REGE 1
00:45
REGE 2
18:35
REGE 3
02:15
Œ
Alternate
CHECK
with
STD-BY Alternate
12:30 with
the menus until the display shows this one:
CHECK / SALT (alternate)
• Press once on ê or é key to make OFF appear
on the lower line
• Press OK to confirm
• Press M during 5 seconds to quit the menu:
the alarm shall disappear

POWER CUT

In case of a power cut during a regeneration, this
process restarts at the beginning of the ongoing
step. In case of a power cut during service, the
softener will restart also in service.

STAND-BY MODE

It is possible to prevent the softener from going
through a regeneration, automatic or manual.

ADVANCED SETTING

Purpose
Enter the password to go through the advanced setting.
Enable / disable the proportional regeneration.
Modify the softening capacity of the device, which has been automati-
cally set once the resin volume was selected (step 3 of regular setting).
Adjust the water consumption per full regeneration.
Only for devices with the salt level follow-up by smartphone app.
Adjust the salt consumption per full regeneration.
Only for devices with the salt level follow-up by smartphone app.
Volume of softened water (read only info). Here: 856 liters.
Peak flow recorded since the last regeneration (read only info). Here:
1068 liters per hour.
Number of regenerations done since the commissioning. May be reset.
Enable / disable the chlorination function
Salt lack alarm enabled / disabled
Code P0011144GR - Rev 10 - 05/03/2019
- 15-
968 The device is in service: it delivers softened water.
12:30 Its treatment autonomy before regeneration is here 968 liters.
Water is being poured into the salt tank (see chapter AD-
VANCED SETTING), it will end in 375 seconds.
The brine is under preparation in the salt tank for the next
regeneration; this step will end here in 180 minutes.
The softener is going through its first active regeneration step,
which will end here in 0 minutes and 45 seconds.
The softener is going through its second active regeneration
step, which will end here in 18 minutes and 35 seconds.
The softener is going through its third active regeneration step,
which will end here in 02 minutes and 15 seconds.
The softener detects a lack of salt and advises to check the salt
SALT
level in the salt tank.
The regeneration function is OFF (see Stand-By mode next
968
page). The softener delivers soft water as long as its autonomy
12:30
allows it (here: autonomy of 968 liters).
This might be useful, for example, while you are
waiting for the intervention of a technician in
case of technical problem. Therefore:
On
• Proceed with a long press (5 seconds) on the
M key
• Then briefly press this M key to go through
the menus until the display shows this one:
• Press once on ê or é key to make ON dis-
played on the lower line
• Press OK to confirm
The display shows then the message STD-BY
alternating with the softener autonomy value.
To cancel this function, you just have to come
back to this STAND-BY menu and turn the lower
line into OFF.
STD-BY
Off
Action
êé to change
OK to confirm
çM to cancel
ê to turn on / off
OK to confirm
çM to cancel
êé to change
OK to confirm
çM to cancel
êé to change
OK to confirm
çM to cancel
êé to change
OK to confirm
çM to cancel
çM to go to next step
çM to go to next step
êé to change
OK to confirm
çM to cancel
êé to change
OK to confirm
çM to cancel
êé to change
OK to confirm
çM to cancel