12.1.2
Prohibited Use / Forseeable Misuse ........................................................................................................................................................ 31
12.2
User requirements .................................................................................................................................................................... 31
12.3
Safety Devices ............................................................................................................................................................................. 32
12.4
General Safety Instructions ................................................................................................................................................ 32
12.5
Electrical Safety .......................................................................................................................................................................... 33
12.6
Special Safety Instructions for that machine .......................................................................................................... 33
12.7
Hazard Warnings ...................................................................................................................................................................... 33
TRANSPORT .................................................................................................................................................. 34
ASSEMBLY ...................................................................................................................................................... 35
14.1
Check scope of delivery ........................................................................................................................................................ 35
14.2
Requirements for the place of installation ............................................................................................................... 35
14.3
Preparation of the surface .................................................................................................................................................. 35
14.4
Assembling the machine ..................................................................................................................................................... 35
14.5
Electrical Connection ............................................................................................................................................................. 37
14.5.1
Setting up a 400 V machine ........................................................................................................................................................................ 38
14.6
Connecting to a dust collection system .................................................................................................................... 38
OPERATION................................................................................................................................................... 38
15.1
Initial check before start ....................................................................................................................................................... 38
15.2
Settings ............................................................................................................................................................................................ 39
15.3
Operation ....................................................................................................................................................................................... 39
15.3.1
Switch the machine on and off ................................................................................................................................................................. 39
15.3.2
Activating/Deactivating the thicknesser feed rate ..................................................................................................................... 40
15.4
Dust collection port ................................................................................................................................................................ 40
15.5
Planing ............................................................................................................................................................................................ 40
15.5.1
Planing small workpieces ............................................................................................................................................................................... 41
15.5.2
Planing with tilted planer fence ................................................................................................................................................................ 41
15.5.3
Planing short workpieces ............................................................................................................................................................................... 41
15.5.4
Planing the workpiece with small cross section............................................................................................................................. 41
15.6
Thicknessing ................................................................................................................................................................................. 41
15.6.1
Converting from planer to thicknessing ............................................................................................................................................. 42
15.6.2
Thicknessing of workpieces ......................................................................................................................................................................... 42
15.7
After working process ............................................................................................................................................................ 43
CLEANING, MAINTENANCE, STORAGE, DISPOSAL .......................................................... 43
16.1
Cleaning .......................................................................................................................................................................................... 43
16.2
Maintenance ................................................................................................................................................................................ 43
16.2.1
Maintenanceplan ................................................................................................................................................................................................ 43
16.3
Checking/adjusting/replacing the V-Belt ................................................................................................................ 44
16.4
Lubricate height adjustment (thicknesser) ............................................................................................................ 44
16.5
Check/Clean anti-kick-back device .............................................................................................................................. 44
16.6
Check/replace Friction wheel (feed) ............................................................................................................................. 45
16.7
Check/lubricate Chain-drive (feed) ............................................................................................................................... 45
16.8
Replacing / adjusting the planing knife ..................................................................................................................... 45
16.9
Storage ............................................................................................................................................................................................. 45
16.10
Disposal ...........................................................................................................................................................................................46
TROUBLESHOOTING .............................................................................................................................. 46
AVANT-PROPOS (FR) ............................................................................................................................. 47
SECURITE ........................................................................................................................................................ 48
19.1
Utilisation conforme ............................................................................................................................................................... 48
19.1.1
Restrictions techniques ................................................................................................................................................................................. 48
19.1.2
Applications interdites / Mauvaises applications dangereuses .......................................................................................... 48
19.2
Exigences des utilisateurs .................................................................................................................................................. 48
19.3
Dispositifs de sécurité ............................................................................................................................................................49
19.4
Consignes générales de sécurité ....................................................................................................................................49
19.5
Sécurité électrique ................................................................................................................................................................... 50
19.6
Instructions spéciales de sécurité pour cette machine ................................................................................... 50
19.7
Mise en garde contre les dangers ................................................................................................................................... 51
TRANSPORT ................................................................................................................................................... 51
MONTAGE ....................................................................................................................................................... 52
21.1
Vérifier l'étendue de la livraison ....................................................................................................................................... 52
21.2
Le lieu de travail ......................................................................................................................................................................... 52
21.3
Préparation de la surface ..................................................................................................................................................... 52
21.4
Assemblage de la machine ................................................................................................................................................ 53
21.5
Raccordement électrique.................................................................................................................................................... 55
21.5.1
Installation d'une machine sur du 400 V ............................................................................................................................................ 55
HOLZMANN MASCHINEN GmbH www.holzmann-maschinen.at
INHALT / INDEX
3
HOB415_400V