Publicité
EnGLIsh
and toward the rear of the saw. To unlock, pull it up and toward
the front of the saw.
nOTE: When ripping, always lock the rail lock lever.
Work Support Extension /Narrow Ripping Fence
Your table saw is equipped with a work support extension to
support work that extends beyond the saw table.
To use the narrow ripping fence in the work support position,
rotate it from its stored position as shown in Fig. N, and slide the
pins into the lower sets of slots
To use the narrow ripping fence in the narrow ripping position,
snap the pins into the upper sets of slots
the fence. This feature will allow 51 mm of extra clearance to the
blade. Refer to Fig. N.
nOTE: Retract the work support extension or adjust to narrow
rip fence position whenever working over the table.
Fine Adjustment Knob
The fine adjustment knob
4
setting the fence. Before adjusting, be sure the rail lock lever is in
its up or unlocked, position.
Rip Scale Pointer
The rip scale pointer will need to be adjusted for proper
performance of the rip fence if the user switches between thick
and thin kerf blades. The rip scale pointer only reads correctly
for position 1 (0 mm to 522 mm), however for position 1 with
narrow rip fence in use add 52 mm. See Adjusting the Rip Scale
under assembly.
Basic Saw Cuts
Ripping (Fig. A, O)
WARNING: Sharp edges.
1. Set the blade to 0°.
2. Lock the rip fence latch
3. Raise the blade until it is about 3 mm higher than the top of
the workpiece.
4. Adjust the position of the fence, refer to Rip
Fence Operation.
5. Hold the workpiece flat on the table and against the fence.
Keep the workpiece away from the blade.
6. Keep both hands away from the path of the blade (Fig. O).
7. Switch the machine on and allow the blade to reach
full speed.
8. Slowly feed the workpiece underneath the guard, keeping it
firmly pressed against the rip fence. Allow the teeth to cut, and
do not force the workpiece through the blade. The blade speed
should be kept constant.
9. Always use a push stick
blade (Fig. O).
10. After completing the cut, switch the machine off, allow the
blade to stop and remove the workpiece.
WARNING:
• Never push or hold the "free" or cut-off-side of the workpiece.
• Do not cut excessively small workpieces.
• Always use a push stick when ripping small workpieces.
Bevel Cuts (Fig. A)
WARNING: Avoid bevel ripping on the beveling (left) side of
the blade.
1. Set the required bevel angle, by rotating lever
it up and to the right.
38
44
on both ends of the fence.
on both ends of
45
allows smaller adjustments when
19
(Fig. A).
22
when working close to the
7
by pushing
2. Set to desired angle, rotate lever by pushing down and to the
left to lock in place.
3. Proceed as for ripping.
Cross-Cutting and Bevel Crosscutting
1. Remove the rip fence and install the mitre gauge in the slot.
2. Lock the mitre gauge at 0°.
3. Proceed as for ripping.
Mitre Cuts (Fig. A)
1. Set the mitre gauge
10
nOTE: Always hold the workpiece tightly against the face of the
mitre gauge.
2. Proceed as for ripping.
Compound Mitre
This cut is a combination of a mitre and a bevel cut.Set the bevel
to the angle required and proceed as for a cross-cut mitre.
Support for Long Pieces
• Always support long pieces.
• Support long workpieces using any convenient means such as
saw-horses or similar devices to keep the ends from dropping.
Dust Extraction (Fig. A)
Dust from materials such as lead-containing coatings and some
wood types, can be harmful to one's health. Breathing-in the
dust can cause allergic reactions and/or lead to respiratory
infections of the user or bystanders. Certain dust, such as oak or
beech dust, is considered carcinogenic, especially in connection
with wood treatment additives.
Observe the relevant regulations in your country for the
materials to be worked.
The vacuum cleaner must be suitable for the material
being worked.
When vacuuming dry dust that is especially detrimental to
health or is carcinogenic, use a dust class M vacuum cleaner.
The machine is provided with a dust exhaust port
the rear of the machine suitable for use with dust extraction
equipment featuring 57/65 mm nozzles. Supplied with the
machine is a reducer port for use of dust extraction nozzles of
34–40 mm diameter.
The blade guard assembly also features a dust exhaust port for
35 mm nozzles and AirLock system.
• During all operations, connect a dust extraction device
designed in accordance with the relevant regulations regarding
dust emission.
• Ensure that the dust extraction hose in use is suitable
for the application and material being cut. Ensure proper
hose management.
• Be aware that man-made materials such as chipboard or MDF
produce more dust particles during cutting than natural timber.
Storage (Fig. A, P)
1. Remove the battery
12
2. Attach push stick
22
to fence.
3. Remove blade guard assembly
Removing the Blade Guard Assembly and Riving Knife. Place
blade guard assembly into holder as shown, then turn lock 1/4
turn to lock in place.
4. Slide closed end of blade wrenches
secure in place with wing nut.
to the required angle.
15
.
. Refer to Installing/
11
into catch then
21
at
Publicité
