Publicité
PR Models: In Enhanced Debit Mode, the top off price can be
set independently (see VALUE OF COIN 2), and the top off time is
calculated according to the following equation:
Top off price
Top off time =
Full cycle price
Penny increment offset is not applied to top off purchases.
Free Cycles
This is established by setting the cycle price to zero. When this
happens, "SELECT CYCLE" will appear rather than a cycle price.
Any cycle started as a free cycle will automatically terminate
when the door is opened.
Debit Card Ready
This washer/dryer is debit card ready. It will accept a variety of
debit card systems, but does not come with a debit card reader.
Refer to the debit card reader manufacturer for proper
washer/dryer setup. In models converted to a Generation 1 debit
card system, debit pulses represent the equivalent of one coin
(Coin 1).
Control Set-up Procedures
IMPORTANT: Read all instructions before operating.
PD/PR Models: Insert service switch key and turn
counterclockwise.
PR Models: Once a Generation 2 debit card reader is installed
(according to the reader manufacturer's instructions), the set-up
modes can only be changed by inserting a set-up card (supplied
by the reader manufacturer) into the card slot. Inserting the
service switch key and turning will only allow access to the
service mode. The washer/dryer is now in the set-up mode. The
lower fabric setting buttons and the lower portion of the display
are used to set up the digital control for the washer. The upper
three fabric setting buttons and the upper portion of the display
are used to set up the controls for the dryer.
The display can contain four numbers and/or letters and a
decimal point on both the top and bottom display portions. These
are used to indicate the set-up codes and related code values
available for use in programming the washer/dryer.
How to Use the Buttons to Program the Controls Washer:
1. POWERWASH — Upper left button is used to adjust the
values associated with set-up codes. Pressing the button will
increment the value. Rapid adjustment is possible by holding
the button down.
2. TEMPERATURE — Lower left button is used to adjust the
values associated with set-up codes. Pressing the button will
decrement the value. Rapid adjustment is possible by holding
down the button.
3. EXTRA RINSE — Lower middle button will advance through
the set-up codes. Pressing the button will advance to the
next available set-up code. Holding the button down will
automatically advance through the set-up codes at a rate of
1 per second.
4. DELICATES — The right button is used to select or deselect
options.
30
Dryer:
1. HEAVY DUTY — Left button is used to adjust the value
x Full cycle length
2. DELICATES — The right button is used to select or deselect
Start Operating Set-up
Washer/dryers are preset at the factory and do not require any
programming. However, if you want to change the settings,
follow the "Set-Up Codes" guide.
The code at the beginning of each segment is the factory default
setting for the PD Models and is the same for the PR Models
unless noted otherwise.
The set-up code is indicated by the one or two left-hand
characters. The set-up code value is indicated by the two or
three right-hand characters.
Set-Up Codes
associated with set-up codes. Pressing the button will
increment the value. Rapid adjustment is possible by holding
down the button.
options.
Code
Explanation
6 06
REGULAR PRICE CYCLE (DRYER)
6 06
Represents the number of Coins or Debit
inputs neededto start the dryer; may adjust
from 0-200 (see b.05 set-up for value of
Coin 1. Advance from 0-200 by pressing
HEAVY DUTY.
6 00
PR Models Only: Factory default of 6 00 or
0.
CYCLE VEND PRICE (WASHER)
6 07
NORMAL Regular Cycle Vend
NORMAL
Price — Represents the number of Coins
or Debit inputs needed to start the washer.
Increase between 0 and 200 by pressing
the POWERWASH button and decrease by
pressing TEMPERATURE button.
6 00
PR Models only: Factory default of 6 00 or
NORMAL
0.
6 07
DELICATES Regular Cycle Vend
DELICATE
Price — Represents the number of Coins
or Debit inputs needed to start the washer.
Increase between 0 and 200 by pressing
the POWERWASH button and decrease by
pressing the TEMPERATURE button.
6 00
PR Models only: Factory default of 6 00 or
DELICATE
0.
6 07
POWERWASH Regular Cycle Vend
POWERWASH
Price— Represents the number of Coins
or Debit inputs needed to start the washer.
Increase between 0 and 200 by pressing
the POWERWASH button and decrease by
pressing the TEMPERATURE button.
6 00
PR Models only: Factory default of 6 00 or
POWERWASH
0.
Press the EXTRA RINSE button once to
advance to next code.
Publicité
