Publicité
3. Close the washer door and the dispenser drawer.
4. To start the washer cleanout cycle, first enter "Service Mode."
Then press and hold the DELICATES button for 2 seconds.
Press the EXTRA RINSE button until P-08 is displayed; then
press the START button to start the cycle.
To exit out of the service mode and activate the clean wash
cycle, push the DELICATES button, then turn the key.
NOTE: The door will lock, the basket will rotate 1/2 turn, then
the door will unlock and lock again, then the washer cleanout
cycle will continue. The washer will not fill, but the basket will
rotate while the washer runs a short sensing cycle. This will
take approximately 3 minutes.
5. The cycle will determine whether clothing or other items are in
the washer.
a. If no items are detected in the washer, it will proceed to
Step 7.
b. If any items are detected in the washer, "F-34" will be
displayed. Then the door will unlock.
Enter the service mode and then press and hold the
START button to cancel the failure code. Then repeat
steps 1, 3, and 4 to start the cycle again.
6. Once the cycle has begun, allow the cycle to complete.
7. After the cycle is complete, leave the door open slightly to
allow for better ventilation and drying of washer interior.
Always do the following to maintain washer freshness:
■ Use only HE (High Efficiency) detergent.
■ Leave the door slightly open after each cycle to allow for
better ventilation and drying of washer interior.
■ Clean the washer monthly using the washer Maintenance
Procedure, using 2/3 cup (160 mL) of liquid chlorine bleach.
■ If the procedure does not sufficiently improve the washer
freshness, please evaluate your installation and usage
conditions for other causes.
Cleaning the exterior
Use a soft damp cloth or sponge to wipe up any spills.
Occasionally wipe the outside of your washer to keep it looking
new. Use mild soap and water. Do not use abrasive products.
Cleaning the dispenser drawer
The dispenser drawer is removable for easy cleaning.
1. Unlock the dispenser drawer for removal by inserting a
flat-blade screwdriver into the catch release. Remove the
dispenser drawer.
2. Remove the inserts (the siphon from the softener and bleach
compartments).
3. Wash the parts under running water.
NOTE: Do not wash components in the dishwasher.
4. Replace the inserts and return the dispenser to the drawer.
Water inlet hoses
Replace the inlet hoses after 5 years of use to reduce the risk of
hose failure. Periodically inspect and replace inlet hoses if bulges,
kinks, cuts, wear, or leaks are found.
When replacing your inlet hoses, record the date of replacement.
28
Dryer
Maintenance instructions:
■ Clean lint screen before and after each cycle.
■ Removing accumulated lint:
From inside the dryer cabinet:
Lint should be removed every 2 years or more often,
depending on dryer usage. Cleaning should be done by a
qualified person.
From the exhaust vent:
Lint should be removed every 2 years, or more often,
depending on dryer usage.
■ Keep area around dryer clear and free from combustible
materials, gasoline and other flammable vapors and liquids.
■ Keep dryer area clear and free from items that would obstruct
the flow of combustion and ventilation air.
If dryer does not operate, check the following:
■ Electrical supply is connected.
■ Circuit breaker is not tripped or house fuse is not blown.
■ Door is closed. Listen closely to hear the door switch activate.
■ Control is set up properly and display shows cycle time.
■ Cycle selection button has been pushed firmly.
■ For gas dryers, check that gas supply shut-off valves are set
in open position.
IF YOU NEED ASSISTANCE
Contact your authorized Maytag
distributor. To locate your authorized Maytag
Laundry distributor, or for web inquiries,
visit www.maytagcommerciallaundry.com.
You will need the washer/dryer model numbers and serial
numbers. Both numbers can be found on the serial-rating plate
located in the dryer door well.
ELECTRONIC CONTROL SETUP
INSTRUCTIONS
Washer Control
Commercial Laundry
®
Commercial
®
Publicité
