Water Filtering; Setting The Filtering Cycles; Suspending The Filtering Cycles; Overheating During Filtering Cycles - Jacuzzi ALIMIA Manuel D'installation

Press the "Econo"
ue. You will then go to the start time (Es).
First set the hour and confirm with the "Econo" key. Then set
the minutes, and press the "Econo" key again to memorize the
set values and exit programming.
When the function is on, the display will shown the respective
symbol.
NOTES
- If a function is turned on (except for the spotlights and/or the
time) when energy savings is present, energy savings is sus-
pended, and the symbol on the display flashes. It restarts au-
tomatically 40 minutes after the function that was started is
turned off.
- The minimum temperature that characterizes energy savings
mode may never be less than 15 °C (59 °F) (minimum main-
tenance temperature).
- If there is a power outage, the set data are stored in memo-
ry. However, when the power comes back on, the function
does not resume. Rather, it is turned on at the set start time.
In addition to the parameters "I1x" (temperature unit of
measure) and "I2x" (limitation of electrical energy con-
sumption), there is also parameter "I3x", the "x" default
value of which is 0. Do not change the setting, otherwise
the electric heater will be turned off.
I

WATER FILTERING

Water filtering is essential to keep the water clean and clear, and
to get rid of suspended particles. This cleaning is provided by the
filtering pump and the cartridge filter located under the overflow
channel (see the chapter on maintenance of the cartridge filter).
The spa is also equipped with a special kind of filtering called
"Instant Clear". This is instantaneous filtering, which differs from
the normal cycle due to its brief, intense duration.
General Information
Filtering occurs during a cycle that is run every 12 hours. This
cycle consists of 2 phases. Depending on the configuration of
electrical consumption limitation (see related chapter), they are
divided as follows:
key again to confirm the selected val- • Start
(with limitation of electrical consumption)
the hydromassage pumps are turned on for 1 minute each, one
at a time. In this phase, the blower runs continuously.
(with limitation of electrical consumption )
the hydromassage pumps and the blower are activated jointly for
1 minute.
• Continuation
This phase is the same for both configurations. The filtering pump
and the Clearray™ run for the time remaining in the cycle.

Setting the filtering cycles

To set the filtering cycle:
Press the key "Filter"
Fdx, where "x" indicates the duration in hours.
Use the keys "Up"
sired duration. This may be from a minimum of 0 to a maximum
of 12 hours, which corresponds to constant filtering, since
the cycle runs every 12 hours in any case.
Press the "Filter"
ue. You will then go to the start time (Fs).
First set the hour and confirm with the "Filter" key. Then set
the minutes, and press the "Filter" key again to memorize the
set values and exit programming.
When the function is on, the display will shown the respective
symbol.
NOTE: if there is a power outage, the set values will be pre-
served.

Suspending the filtering cycles

The filtering cycle may be suspended by the anti-freeze pro-
tection ("Smart Winter") or due to overheated water. Refer to the
respective chapters.
If the system is in standby mode (see related chapter), the fil-
tering pump stops and is restarted when the system is no longer
in standby mode.
If there is a power outage during a filtering cycle, or if it occurs
prior to the start of filtering and lasts after that time, the cycle will
not start when the power comes back on. Filtering will be postponed
until the next cycle, since the cycle is repeated every 12 hours.

Overheating during filtering cycles

During the filtering cycle, if the water temperature exceeds
the setpoint by more than 1 °C (2 °F) (see the chapter on ad-
justing the water heating temperature) and it does not decrease
at least 1 °C (2 °F) in the following 3 hours, the filtering cycle
will be suspended.
Even if the water temperature is high (due to excessive sunlight,
for example), filtering is however ensured for at least 3 hours.
32
. The display shows the message
and/or "Down" to insert the de-
key again to confirm the selected val-