Important Product Information
Certifications
This product meets the Essential Requirements of all rel-
evant European directives and is eligible for CE marking.
BLX1, BLX2
Certified under FCC Part 74.
Certified by IC in Canada under RSS-123 and RSS-102.
FCC ID: DD4BLX1A, DD4BLX1B, DD4BLX1C,
DD4BLX1D; DD4BLX2A, DD4BLX2B, DD4BLX2C,
DD4BLX2D. IC: 616A-BLX1A, 616A-BLX1B,
616A-BLX1C, 616A-BLX1D; 616A-BLX2A, 616A-BLX2B,
616A-BLX2C, 616A-BLX2D
BLX4, BLX88
Approved under the Declaration of Conformity (DoC) pro-
vision of FCC Part 15.
Band
Range
H8E
518 to 542 MHz
K3E
606 to 630 MHz
K14
614 to 638 MHz
M17
662 to 686 MHz
Q25
742 to 766 MHz
R12
796 to 806 MHz
S8
823 to 832 MHz
T11
863 to 865 MHz
NOTE: This Radio equipment is intended for use in musi-
cal professional entertainment and similar applications.
This Radio apparatus may be capable of operating on
some frequencies not authorized in your region. Please
contact your national authority to obtain information on
authorized frequencies and RF power levels for wireless
microphone products.
English
LICENSING INFORMATION
Licensing: A ministerial license to operate this equipment
may be required in certain areas. Consult your national
authority for possible requirements. Changes or modifica-
tions not expressly approved by Shure Incorporated could
void your authority to operate the equipment. Licensing
of Shure wireless microphone equipment is the user's
responsibility, and licensability depends on the user's clas-
sification and application, and on the selected frequency.
Shure strongly urges the user to contact the appropriate
telecommunications authority concerning proper licensing,
and before choosing and ordering frequencies.
Information to the user
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or
more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and
the receiver.
•
Connect the equipment to an outlet on a circuit
different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV
Output Power
technician for help.
10 mW
This device complies with Industry Canada licence-exempt
RSS standard(s). Operation of this device is subject to the
10 mW
following two conditions: (1) this device may not cause
10 mW
interference, and (2) this device must accept any interfer-
ence, including interference that may cause undesired
10 mW
operation of the device.
Le présent appareil est conforme aux CNR d'Industrie
10 mW
Canada applicables aux appareils radio exempts de
10 mW
licence. L'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne doit pas produire de brouillage,
10 mW
et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible
10 mW
d'en compromettre le fonctionnement.
This Class B digital apparatus complies with Canadian
ICES-003. Cet appareil numérique de la classe B est con-
forme à la norme NMB-003 du Canada.
Note: EMC conformance testing is based on the use of
supplied and recommended cable types. The use of other
cable types may degrade EMC performance.
Changes or modifications not expressly approved by
the manufacturer could void the user's authority to
operate the equipment.
Please follow your regional recycling scheme for batteries,
packaging, and electronic waste.
9