Publicité
Les langues disponibles
Les langues disponibles
For your personal protection and the protection
of people nearby, suitable hearing protection
must be worn.
- Do not get distracted and always concentrate
on what you are doing. Use common sense.
Never operate the tool when you are tired, sick
or under the influence of alcohol or other drugs.
Additional general safety instructions
- Do not handle the plug or the tool with wet
hands and do not use the tool in the rain.
- Use only outdoor rated extension leads that
are so marked. Keep the extension cord away
from heat, oil and sharp edges.
- Use a power cable H05 RN-F or H05 VVF or
greater, with minimum cross section of 2 x1.5
mm² and max length of 20 m.
- Use a face mask if dusty.
- Keep clear of discharge openings at all times.
- Do not use solvents or cleaning liquids to clean
your Machine - use a blunt scraper to remove
grass and dirt. Always disconnect from the
electrical supply before cleaning.
- Keep your working area clean and tidy. Untidy
and poorly lit working areas may lead to ac-
cidents.
- Do not operate the tool in potentially explosive
environments containing combustible fluids,
gases or dusts.
- Avoid physical contact with earthed surfaces
as pipes, heaters, ovens and refrigerators.
- Store power tools out of the reach of children.
Do not allow persons to use the tool if they are
not familiar with the tool or these instructions.
- Do not overtax the power tool. Use the power
tool intended for your type of work in each case.
- Do not use the cable to carry or hang up the
tool or to pull the plug out of the socket. Keep
the cable away from heat, oil and sharp edges
or moving parts of the tool. Damaged or tan-
gled cables increase the risk of electric shock.
- Do not overestimate your abilities. Take care
of a safe footing and keep your balance at all
times.
- Remove adjustment tools or wrenches and the
like before you switch the tool on.
- Avoid unintentional operation. Make sure that
the switch is in 'OFF' position before pulling
the plug from the mains socket. When carrying
the tool with your finger on the on/off switch or
connecting the tool to the mains supply with
GB | Operating Instructions
- Always pay attention to what you do and apply
- Thoroughly maintain your power tool. Check
- Use power tools, accessories, add-on tools,
- Have the power tool serviced by qualified tech-
- Replace worn or damaged parts for reasons
- Grip guide bar firmly with both hands. Never
- Hold the guide bar and lift the tool to move it
Electrical safety
- The electric motor has been designed to use
- Make sure your voltage corresponds to the
- Always use a plug compulsory for double insu-
- Always switch your machine off before discon-
- Use only extension cords that are approved for
GB-5
the switch in 'ON' position, this may result in
accidents.
reasonable care when working with a power
tool. Do not use the tool when you are tired
or under the influence of medication, drugs
or alcohol.
whether moving parts are working properly
and are not jamming/sticking, and whether
parts are broken or otherwise damaged in a
way that affects the function of the tool. Have
damaged parts repaired before using the tool.
etc. in accordance with these instructions and
in the way prescribed for the respective type
of tool. You should also consider the working
conditions and the work to be carried out.
nical personnel only; repairs should be carried
out using exclusively original spare parts.
of safety. Use only original spare parts. Parts
not produced by the original manufacturer may
have a poor fit and possibly cause injury.
operate the tool with only one hand.
from one place to another. Always switch off
the tool, disconnect the plug and wait until the
application stops before carrying out mainte-
nance.
single phase voltage only.
one written on the rating label.
Your machine has double insulation
in conformity to Directive EN 60335,
you do not therefore need to earth.
lation electric tooling when replacing the cable.
necting any plug, socket or extension.
out-door use and are not lighter than rubber-
sheathed cables of type H07 RN-F according
to DIN/VDE 0282 with a diameter of at least
1.5 sq. mm. They cords must be splash-proof.
Publicité
