Scheppach HC51 Traduction Des Instructions D'origine page 87

AC motor
• The mains voltage must be 230 V~
• Extension cables up to 25 m long must have a
cross-section of 1.5 mm .
2
Connections and repairs of electrical equipment may
only be carried out by an electrician.
Please provide the following information in the
event of any enquiries:
• Type of current for the motor
• Machine data - type plate
• Motor data - type plate
10. Cleaning, maintenance and storage
m Important!
Pull out the power plug before doing any cleaning
and maintenance work on the equipment. Risk of in-
jury from electric shock!
m Important!
Wait until the equipment has cooled down complete-
ly! Risk of burns!
m Important!
Always depressurize the equipment before carrying
out any cleaning and maintenance work! Risk of in-
jury!
10.1 Cleaning
• Keep the equipment free of dirt and dust as far as
possible. Wipe the equipment with a clean cloth or
blow it down with compressed air at low pressure.
• We recommend that you clean the equipment im-
mediately after you use it.
• Clean the equipment regularly with a damp cloth
and some soft soap. Do not use cleaningagents or
solvents; these may be aggressive to the plastic
parts in the equipment. Ensure that no water can
get into the interior of the equipment.
• You must disconnect the hose and any spraying
tools from the compressor before cleaning. Do not
clean the compressor with water, solvents or the
like.
10.2 Maintenance work on the pressure vessel
(Fig. 1)
m Important!
To ensure a long service life of the pressure vessel
(11), drain off the condensed water by opening the
drain valve (10) each time after using.
Release the vessel pressure first (see 10.7.1).
Open the drain screw by turning counter-clockwise
(looking at the screw from the bottom of the com-
pressor) so that all the condensed water can run out
of the pressure vessel. Then close the drain screw
again (turn it clockwise). Check the pressure vessel
for signs of rust and damage each time before using.
Do not use the compressor with a damaged or rusty
pressure vessel. If you discover any damage, then
please contact the customer service workshop.
m Important!
The condensed water from the pressure vessel will
contain residual oil. Dispose of the condensed water
in an environmentally compatible manner at a suita-
ble collection point.
10.3 Safety valve (Fig. 11)
The safety valve (8) has been set for the highest per-
mitted pressure of the pressure vessel. It is not per-
mitted to adjust the safety valve or remove the con-
nection lock (8.2) between the exhaust nut (8.1) and
its cap (8.3).
Actuate the safety valve every 30 operating hours but
at least 3 times a year, to ensure that it works when
required. Turn the perforated exhaust nut (8.1) coun-
terclockwise to open it and use your hands to pull the
valve rod outwards over the perforated exhaust nut
(8.1) to open the safety valve outlet. Now, the valve
audibly releases air. Then, tighten the exhaust nut
clockwise again.
10.4 Checking the oil level at regular intervals
(Fig. 2)
Place the compressor on a level and straight surface.
The oil level must be between the MAX and MIN
marks on the oil level window (16).
Oil change: Recommended oil: SAE 30 (viscosity 30)
or L-DAB 100 over 10 °C
SAE 10 (viscosity 10) or L-DAB 68 below 10 °C
The original oil filling must be changed after 10 hours
in operation; thereafter the oil must be drained and
replaced with new oil after every 50 hours in oper-
ation.
10.5 Changing the oil (Fig. 1 - 3)
Switch off the engine and pull the mains plug out of
the socket. Remove the oil sealing plug (14). After
releasing any air pressure you can unscrew the oil
drain plug (9) from the compressor pump (19).
To prevent the oil from running out in an uncontrolled
manner, hold a small metal chute under the opening
and collect the oil in a vessel.
If the oil does not drain out completely, we recom-
mend tilting the compressor slightly. When the oil
has drained out, re-fit the oil drain plug (9).
Dispose of the old oil at a drop-off point for old oil.
To fill in the correct quantity of oil, make sure that the
compressor stands on an even surface. Fill new oil
through the oil filler opening (18) until it comes up to
the maximum level. This is marked with a red dot on
the oil level window (16) (Fig. 2).
www.scheppach.com
GB | 87