Scheppach HC51 Traduction Des Instructions D'origine page 85

• Do not process media such as white spirit, butyl
alcohol and methylene chloride with the PVC pres-
sure hose. These media will destroy the pressure
hose.
• The work area must be separated from the com-
pressor so that it cannot come into direct contact
with the working medium.
Operating pressure vessels
• You must keep your pressure vessel in good work-
ing order, operate the vessel correctly, monitor the
vessel, carry out necessary maintenance and re-
pair work immediately and meet the relevant safety
precautions.
• The supervisory authority may enforce essential
control measures in individual cases.
• A pressure vessel is not allowed to be used if it has
faults or deficiencies that can endanger workers
or third parties.
• Check the pressure vessel for signs of rust and
damage each time before using. Do not use the
compressor with a damaged or rusty pressure ves-
sel. If you discover any damage, then please con-
tact the customer service workshop.
Do not lose these safety instructions
6. Technical data
Mains connection
Motor rating
Operating mode
Compressor speed
Pressure vessel capacity
Operating pressure
Theoretical intake capacity
Theoretical delivery rate
Protection type
Weight of the unit
Oil
Max. altitude
(above mean sea level)
Noise data
The noise emission values were measured in ac-
cordance with EN ISO 3744.
Wear hearing protection.
The effects of noise can cause a loss of hearing.
m Warning: Noise can have serious effects on your
health. If the machine noise exceeds 85 dB (A),
please wear suitable hearing protection.
230 V / 50 Hz
1800 W
S1
2850 min
-1
50 l
approx. 10 bar
approx. 257 l/min
approx. 193 l/min
IPX2
approx. 34 kg
approx. 0,3 l
1000 m
www.scheppach.com
Sound power level L
wA
Sound pressure level L
pA
Uncertainty K
wA/pA
7. Before starting the equipment
• Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Prior to initial commissioning, remove the trans-
•
port plug (14) and fill the crank housing with oil as
described in item 8.3.
• Check the equipment for damage which may have
occurred in transit. Report any damage immedi-
ately to the transport company which was used to
deliver the compressor.
• Install the compressor near the point of consump-
tion.
• Avoid long air lines and supply lines (extension
cables).
• Make sure that the intake air is dry and dustfree.
• Do not install the compressor in a damp or wet
room.
• The compressor may only be used in suitable
rooms (with good ventilation and an ambient tem-
perature from +5 °C to 40 °C). There must be no
dust, acids, vapors, explosive gases or inflamma-
ble gases in the room.
• The compressor is designed to be used in dry
rooms. It is prohibited to use the compressor in
areas where work is conducted with sprayed water.
• The oil level in the compressor pump has to be
checked before putting the equipment into oper-
ation.
• The compressor may only be used outdoor briefly
when the ambient conditions are dry.
• The compressor must always be kept dry and must
not be left outdoors after work is complete.
8. Attachment and operation
m Important!
You must fully assemble the appliance before using it
for the first time!
8.1 Wheels (Fig. 4)
1. To attach the wheels (12), pass a washer with the
wheel bolt through the wheel. Then add a wash-
er and a hexagon nut on the inside of the wheel.
Fasten the nut by hand so that the wheel still can
be rotated.
2. Push the wheel unit through the ear below the
tank.
3. Fasten it with a washer, a safety washer and a nut
and tighten them securely.
4. Repeat this process with the second wheel.
97 dB(A)
74,2 dB(A)
2,37 dB(A)
GB | 85