Residual Risk - PrimAster PMAAS 40 Manuel D'utilisation

GB ENGLISH
- Correct position of shoulder strap and inspection of the
quick release mechanism
- Damage to the device like cracks on the guide rail
- Correct guide rail seating
- Installation/running direction of the problem-free
(sharp) saw chain
- Saw chain tension (in case of a new chain, check and
readjust this multiple times)
- Functioning chain lubrication
Check the automatic chain lubrication
Installing the shoulder strap
1. Position the shoulder strap so that the strap is over
the left shoulder (Chapter II).
2. Attach the snap hook to the shaft bracket on the
shaft (Chapter II).
Position the shoulder strap so that the strap is over the
left shoulder (Chapter II).
Attach the snap hook to the shaft bracket on the shaft
(Chapter II).
Never carry the belt diagonally across your shoulders and
chest, but rather only on one shoulder, so that you can
rapidly move away from the tool in case of danger.
Regularly check the function of the automatic chain lub-
rication to prevent overheating and associated damage
to the blade and saw chain. To do this, point the tip of
the sword against a smooth surface (board, section of a
tree) and let the chainsaw run. If an increasing amount of
oil becomes visible during this procedure, the automatic
chain lubrication is working properly.
WARNING! Danger of injury!
If the shoulder strap is not detached promptly in an emer-
gency, serious injuries can result.
WARNING
Keep your working position in mind to ensure safe
working. Do not use the pole-mounted pruner from
a ladder or other unsafe position. Ensure that you
have firm footing and use appropriate protective
clothing. Do not be tempted to make ill-considered
cuts. This can endanger yourself and others.
Cutting springpoles
A springpole is any log, branch, rooted stump, or sapling
which is bent under tension by other wood so that it
springs back if the wood holding it is cut or removed.
On a fallen tree, a rooted stump has a high potential of
springing back to the upright position during the bucking
cut to separate the log from the stump. Watch out for
springpoles—they are dangerous.
28
WARNING
Springpoles are dangerous and could strike the
operator, causing the operator to lose control of the
chain saw. This could result in severe or fatal injury
to the operator. This should be done by trained
users.
Some regions have regulations that restrict the use of the
machine. Check with your local authority for advice.
Never allow children or people unfamiliar with the
instructions to use the machine. Local regulations may
restrict the age of the operator.
Ensure before each use that all controls and safety
devices function correctly. Do not use the machine if the
"off" switch does not stop the motor.
Do not wear loose fitting clothing, short trousers, or
jewellery of any kind.
Secure long hair so it is above shoulder level to prevent
entanglement in moving parts.
Beware of thrown, flying, or falling objects. Keep all
bystanders, children, and animals at least 15 m away from
the work area.
Do not operate in poor lighting. The operator requires a
clear view of the work area to identify potential hazards.
Use of hearing protection reduces the ability to hear
warnings (shouts or alarms). The operator must pay extra
attention to what is going on in the work area.
Operating similar tools nearby increases both the risk
of hearing injury and the potential for other persons to
enter your work area.
Keep firm footing and balance. Do not overreach.
Overreaching can result in loss of balance and can increa-
se the risk of kickback.
Keep all parts of your body away from any moving part.
Inspect the chain saw before each use. Check for correct
operation of all controls, including the chain brake. Check
for loose fasteners, make sure all guards and handles are
properly and securely attached. Replace any damaged
parts before use.
Do not modify the machine in any way or use parts and
accessories which are not recommended by the manu-
facturer.
WARNING
If the machine is dropped, suffers heavy impact or
begins to vibrate abnormally, immediately stop
the machine and inspect for damage or identify
the cause of the vibration. Any damage should be
properly repaired or replaced by an service station.

Residual Risk

Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual
risk factors. The following hazards may arise in use and