Emerson AVENTICS PROFINET-IO XVES Notice D'instruction page 20

Designation Color
DIAG Green
Red
Red
BF Red
Red
-
SF Red
Red
-
L/A 1 Green
L/A 2
Yellow
-
11.3 Pin assignment
Table 6: Pin assignment X7E1/X7E2
Pin Meaning
1 TD+
2 RD+
1 2
3 TD-
4
3
4 RD-
Housing Ground
Table 7: Pin assignment power supply
Pin Meaning
1 24 V DC power supply of the sensors/electronics (UL)
2 24 V DC actuator voltage (UA)
2 1
3 0 V DC power supply of the sensors/electronics (UL)
3 4
4 0 V DC actuator voltage (UA)
12 Disposal
Improper disposal will lead to pollution of the environment. Furthermore, the
materials can no longer be recycled.
Dispose of the product, the packaging and any escaping operating materials
u
in accordance with the applicable national regulations.
13 Troubleshooting
13.1 Procedure
Step 1: Check the system
In case of malfunctions, first check the system or the system part where the
u
product is installed. Check the following items:
• All connections. See g 9. Service.
• Settings. See g 14. Technical
Step 2: Check the product
1. Make sure the system or system part is not under pressure or voltage.
2. Check the product based on the fault patterns described below.
3. Perform troubleshooting using the information under "Remedy".
If the malfunction cannot be eliminated as described under "Remedy": Disas-
semble the product and return it. See
4. After the malfunction has been eliminated; Put the system or product back
into operation.
AVENTICS™ PROFINET-IO | 570088-BAL-AA | English
State Meaning
Illuminates State of the hardware is ok
Flashes (1 Hz) Diagnostic message of the product
available
Illuminates Hardware error of the valve system
Flashes (1 Hz) Connection to master interrupted
Illuminates No configuration
No physical connection
Slow physical connection
Off The product exchanges data cycli-
cally with the control.
Flashes (1 Hz) DCP signal service initiated via the
bus.
Illuminates Watchdog timeout
Channel diagnosis, general diagno-
sis or extended diagnosis available.
System error
Off No error
Illuminates Physical connection to network de-
tected.
Flashes Receive data package.
Off No physical connection to network
detected.
data.
g 4.3 Returning the product.
13.2 Malfunction types
Error Possible cause
No output pressure at the • No power supply con-
valves nected to the product.
See LED display
• No supply pressure avail-
able.
Output pressure too low Supply pressure too low.
Power supply for the product
not sufficient.
Air is audibly escaping Leakage between product
and supply.
Pneumatics incorrectly con-
nected.
Name was not deleted when A save operation was trig-
setting the address 0x00 gered before the address
0x00 was set
LED UL/UA flashes green The supply voltage is less
than the lower tolerance limit
(18 V DC) and more than
10 V DC
LED UL/UA illuminates red The valve supply voltage is
less than 21.6 V DC
LED UL/UA is off The supply voltage is less
than 10 V DC
LED UL/UA flashes red The supply voltage is greater
than 26.4 V DC
LED DIAG flashes red No module connected to the
product
Diagnostic message for open
load/short circuit at valve
available.
LED DIAG illuminates red Diagnostic message available. Check module.
Internal connection error or
hardware error.
Product is not detected.
LED BF illuminates red Serious network error
LED BF flashes red Connection to master has
been disconnected. No com-
munication via PROFINET IO
possible.
Error in the PLC configuration. Check PLC configuration.
LED L/A 1 or LED L/A 2 illumi- No data exchange with the
nates green and flashes yel- bus coupler.
low
Bus coupler has not been con-
figured in the control.
LED L/A 1 or LED L/A 2 is off No connection to network
participant.
Connecting cable damaged.
Network participant dam-
aged.
Product damaged.
14 Technical data
This section contains an excerpt of the most important technical data. Further
technical data can be found on the product page in the Emerson store.
Remedy
Apply power supply on plug
connector X1S.
Check power supply polarity.
Switch on system compo-
nent.
Connect supply pressure.
Increase supply pressure.
Check LED on the product.
Apply sufficient power sup-
ply.
Check the supply connection.
Check the pneumatic connec-
tion.
1. Separate power supply
2. Set the address between
1 and 254 (0x01and
0xFE).
3. Establish the power sup-
ply.
4. Wait 5 s, then separate
power supply.
5. Set address switch to
0x00.
6. Establish the power sup-
ply.
Check power supply on plug
connector X1S.
Connect the module.
Check the connection of the
valves.
Contact manufacturer
Check network settings
Check the connection to the
master.
Connect network section with
the control.
Bus coupler configured in the
control.
Connect fieldbus connection
X7E1 or X7E2 to network par-
ticipant.
Replace connecting cable.
Replace network participant.
Replace product.
20