PIKO 37452 Manuel D'utilisation page 5

Getting Started: Initial Operation
Unpacking the Model
Remove the styrofoam packaging
extremely carefully to prevent
damaging accessories and attached
parts such as handrails etc.
Initial Operation
We recommend letting the locomotive
run without a train for 30 minutes
in both directions, to properly break
it in. This will help achieve optimal
performance and longevity for the
locomotive. Of course, your model
should only be run on smooth and
perfectly clean tracks with reliable
electrical contact to all track sections.
Technical Data
Power Supply
The model should only be operated on
a pure, filtered DC power supply of 0
to 24 volts, with a capacity of at least
2 Amp and a fast-acting fuse or circuit
breaker to protect against short circuits.
Do not use a power supply which is not
in safe and perfect working condition.
(See "Digital Decoder" section for
operation on digital power.)
Mechanism
The locomotive has two powerful high-
precision motors, which turn the wheels
through a robust gearbox.
Lighting
The model is equipped with automatic
directional headlights, using white/
red LEDs for a realistic appearance. The
"front" lights are illuminated according
to the travel direction.
Digital and sound system
The model is factory-prepared for the
installation of a PIKO SmartDecoder.
Furthermore, a PIKO SmartDecoder
sound system with original sound
can also be retrofitted. The PIKO
SmartDecoder sound system
is equipped with a broadband
loudspeaker with waterproof
membrane. After installation of the
PIKO SmartDecoder sound system,
the locomotive can be used with all
its digital functions on digital layouts.
When used on analog layouts, only
the driving sound of the locomotive is
reproduced.
Analog version
Digital Decoder
The analog model is prepared at
the factory for use with the PIKO
SmartDecoder XP Art. No. #36500. After
plugging in the decoder, the locomotive
can be used on both digital and analog
layouts.
Sounddecoder
The analog model is factory prepared
for the installation of the PSD XP Sound
#36544 with original sound.
The PSD XP Sound #36544 comes with
a full range speaker with waterproof
membrane.
After installation of the PSD XP, the
locomotive can be used with all its digital
functions on digital layouts. When used
on analog layouts, only the driving noise
of the locomotive is reproduced.
Digital sound version
The digital sound version got all
features since leaving the factory.
#35268 Track switch magnet
In the digital sound version there is a
sensor (reed contact),which reacts to
each track switching magnet #35268
and triggers either a whistle or horn.
Maintenance
Lubrication
After each 25 hours of operation, and
after any long periods of storage, please
lubricate the locomotive's gears with a
sparing amount of plastic-compatible,
non-hardening grease. Remove the
gearbox bottom cover and be careful
to keep the front and rear wheelsets
aligned with each other. Be sure to
securely retighten the gearbox bottom
cover screws.
Cleaning
If cleaning is necessary, use only a
mild cleaning agent (such as soap and
water) and gentle action with a soft
non-abrasive cloth or brush. Never
immerse the loco in liquid or "flood"
any internal parts!
Wheel Wipers and pick-Up shoes
should be changed after 500 hours of
operation.
Please Note! Damage to Carpets
and Other Surfaces: Normal
operation of the locomotive
causes wear of mechanical parts
(wheels, electrical pickups etc.). This
produces carbonized dust, grease
and oil, which can permanently
stain carpets, wood floors and
other materials. It is the user's
responsibility to take proper
precautions against this damage.
Wipe any grease or oil from the
track rails with a clean soft cloth.
PIKO Spielwaren GmbH, as well as
its representatives, distributors and
retailers, assume no liability for any
such damage.
Please Note!
Important Safety Precautions
• Check the power supply regularly
for any damage or problems.
• Do not use a malfunctioning or
damaged power supply!
• This model must only be operated
with one power source per circuit!
• This product is not a toy, not suitable
for personnel under 14 years of age.
This product has small parts, sharp
parts, and moving parts.
• This model must only be operated
with a safety-assured power supply
with the
identification!
• The power supply is not a toy!
• Disconnect the model from the
power supply before cleaning or
servicing!
• Do not insert the track power
connecting wires into household
"mains" voltage outlets.
5