Lenze starttec 1 Instructions De Montage page 91

Show/Hide Bookmarks
Switch-on sequence
13. Setting of switch on and switch off
delay for the brake: delay for the brake:
Switch on delay t
Switch off delay t Switch off delay t
Lenze setting: 0.00 s
14. Use C0002 to save the settings in
the hand terminal to be able to
transfer them to other starttecs.
15. If you want to change the settings,
please go to the menu
( ^ 86)
When you are ready with parameter setting:
16. starttec enable
17. If necessary, release the brake
18. Start drive 8
19. The drive should be running now
20. If you remove the hand terminal do
not forget to seal the AIF interface
with the rubber cap enclosed in the
delivery package.
L
z z z z z z z z z
w x w x w x w x w x w x w x w x w x
y y y y y y y y y
(C0423)
Bon
(C0424) (C0424)
Boff B ff
z z z z z z z z z
w x w x w x w x w x w x w x w x w x
y y y y y y y y y
CINH CINH CINH CINH CINH CINH CINH CINH CINH
E1 E1 E1 E1 E1 E1 E1 E1 E1
M M M M M M M M M
E3 E3 E3 E3 E3 E3 E3 E3 E3
B B B B B B B B B
z
w x
y
E.g. change of deceleration time
(C0013), change of initial voltage
A A A A L L L L L L L L
.
(C0016), change of activation class
(C0121)
Terminal X3/28 = HIGH
Terminal X3/E3 = HIGH
Motor 1 start Terminal X3/E1 = HIGH
CINH CINH CINH CINH CINH CINH
E1 E1 E1 E1 E1 E1
M M M M M M
E3 E3 E3 E3 E3 E3
EDK71MMXXX-010 DE/EN/FR 2.0
Commissioning
With hand terminal
d d d d d d d d d c c c c c c c c c
        
j j j j j j j j j g g g g g g g g g f f f f f f f f f k k k k k k k k k i i i i i i i i i h h h h h h h h h PS PS PS PS PS PS PS PS PS
0 0 0 0 0 0 0 0 0 4 4 4 4 4 4 4 4 4 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 o o o o o o o o o
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
d d d d d d d d d c c c c c c c c c
        
j j j j j j j j j g g g g g g g g g f f f f f f f f f k k k k k k k k k i i i i i i i i i h h h h h h h h h PS PS PS PS PS PS PS PS PS
0 0 0 0 0 0 0 0 0 4 4 4 4 4 4 4 4 4 2 2 2 2 2 2 2 2 2 4 4 4 4 4 4 4 4 4
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 o o o o o o o o o
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
start014
t t t t t t t t t
t ir t ir t ir t ir t ir t ir t ir t ir t ir
t if t if t if t if t if t if t if t if t if
t Bon t Bon t Bon t Bon t Bon t Bon t Bon t Bon t Bon t Boff t Boff t Boff t Boff t Boff t Boff t Boff t Boff t Boff
start041
d c

j g f k i h PS
0002
000
000
start042
t t t t t t
t ir t ir t ir t ir t ir t ir t if t if t if t if t if t if
start013
Note
CINH Enable starttec via X3/28
1 1 1 1 1 1 1 1 1
E1 Motor 1 start
M Voltage characteristic at
1U, 1V, 1W (motor 1)
1 1 1 1 1 1 1 1 1
E3 Control of brakes B1, B2
B Brake voltage
characteristic for B1, B2
t Acceleration time
ir
t Deceleration time
if
t Delay time until brake
Bon
releases
t Delay time until brake
Boff
blocks
See Code Table ( ^ 92)
1
A
See Code Table ( ^ 92)
CINH Enable starttec via X3/28
E1 Motor 1 start
M1 Voltage characteristic at
1U, 1V, 1W (motor 1)
E3 Control of brakes B1, B2
t Acceleration time
ir
t Deceleration time 0.5 s
if
(C0013)
If the drive does not start,
press u in addition
Otherwise protection class
IP65 cannot be guaranteed.
7
91