Keysight PV8900 Serie Guide D'utilisation Et De Maintenance page 38

1 Quick Reference
Characteristic
Maximum load inductance: 8
Line regulation
Voltage and current::
Typical leakage current
Output disabled, or unplugged from ac mains:
Bleed resistor
+/- Terminals to chassis ground:
1 200/208 Vac input reduces the current and power rating 50%; 200/208 Vac input is only available with firmware rev B.06.03.1003 and up
2 Applies for ambient temperatures above 30°C or below 20°C
3 From occurrence of over-voltage to start of shutdown
4 With no load and a step change from 0.1% to 100% of voltage rating; bandwidth frequency = 100 kHz
5 With 1 µF capacitive load and a step change from 100% to 0.1% of voltage rating; bandwidth frequency = 100 kHz
6 With ac short and a step >10% of output voltage rating; bandwidth frequency = 100 kHz
7 Time from when the Output On command is received to the initiation of turning the output on
8
Unit is susceptible to internal damage if Maximum Load Inductance limits are exceeded at the rated current
9 Due to the pre-regulation circuits in the unit, the line regulation is not measurable
Common Characteristics
Common Characteristic
Command Processing Time
Constant Dwell ARBs
Number of points:
Dwell range:
Dwell resolution:
Computer Interfaces
LXI version:
LXI extended functions:
LAN:
USB:
GPIB:
Digital Port
Max voltage rating:
Pins 1 & 2 as FLT:
Pins 1-7 as outputs:
Pins 1-7 as inputs:
Pin 8:
38
PV8921A
740 µH
See Note 9
1 mA
68 MΩ
≤ 1 ms from receipt of command to start of output change. Applies to simple settings commands
over the GPIB interface (see Typical Command Processing
Up to 65,535
One dwell setting applies for the entire ARB, from 10.24 µs to 0.30 seconds
Values are rounded to the nearest 10.24-microsecond increment
1.5 LXI Device Specification 2016
LXI IPv6, LXI HiSLIP, LXI VXI VXI-11 Discovery and Identification
10 Mb, 100 Mb, 1 Gb LAN
USB 2.0 (USB-TMC488 protocol)
SCPI - 1993, IEEE 488.2 compliant interface
+16.5 Vdc/- 5 Vdc between pins
Maximum low-level output voltage = 0.5 V @ 4 mA
Maximum low-level sink current = 4 mA
Typical high-level leakage current = 1 mA @ 16.5 Vdc
Maximum low-level output voltage = 0.5 V @ 4 mA;
1 V @ 50 mA; 1.75 V @ 100 mA
Maximum low-level sink current = 100 mA
Typical high-level leakage current = 0.8 mA @ 16.5 Vdc
Maximum low-level input voltage = 0.8 V
Minimum high-level input voltage = 2 V
Typical low-level current = 2 mA @ 0 V (internal 2.2k pull-up)
Typical high-level leakage current = 0.12 mA @ 16.5 Vdc
Pin 8 is common (internally connected to chassis ground)
Keysight PV8900 Series Operating and Service Guide
PV8922A PV8931A
740 µH 320 µH
See Note 9 See Note 9
1 mA 1 mA
68 MΩ 68 MΩ
All Models
Times)
PV8932A
490 µH
See Note 9
1 mA
68 MΩ