Manufacturer's Warranty - Hilti DSH 700 Mode D'emploi

two years. If any emission related part on your engine
(as listed above) is defective, the part will be repaired or
replaced by Hilti.
Owner's warranty responsibilities
As a small non-road engine owner, you are responsible
en
for performance of the required maintenance as defined
by Hilti in the owner's manual. Hilti recommends that you
retain all receipts covering maintenance on your small
non-road engine, but Hilti cannot deny warranty solely
for the lack of receipts or for your failure to ensure the
performance of all scheduled maintenance. Any replace-
ment part or service that is equivalent in performance
and durability may be used in non-warranty maintenance
or repairs, and shall not reduce the warranty obligations
of the engine manufacturer. As the small non-road equip-
ment engine owner, you should be aware, however, that
Hilti may deny you warranty coverage if your small non-
road engine or a part en of it has failed due to abuse,
neglect, improper maintenance, unapproved modifica-
tions or the use of parts not made or approved by the
original equipment manufacturer. You are responsible for
presenting your small non-road engine to Hilti as soon
as the problem exists. The warranty repairs should be
completed in a reasonable amount of time, not to exceed
30 days.
Coverage
Hilti warrants to the ultimate purchaser and each sub-
sequent purchaser that your small non-road equipment
engine will be designed, built equipped, at the time of
sale, to meet all applicable regulations. Hilti also warrants
to the initial purchaser and each subsequent purchaser
that the emission-related warranted parts are free from
defects in material and workmanship which cause the
engine to fail to conform with applicable regulations for a
period of two years. These warranty periods will begin on

12 Manufacturer's warranty

Hilti warrants that the tool supplied is free of defects in
material and workmanship. This warranty is valid so long
as the tool is operated and handled correctly, cleaned
and serviced properly and in accordance with the Hilti
Operating Instructions, and the technical system is main-
tained. This means that only original Hilti consumables,
components and spare parts may be used in the tool.
This warranty provides the free-of-charge repair or re-
placement of defective parts only over the entire lifespan
of the tool. Parts requiring repair or replacement as a
result of normal wear and tear are not covered by this
warranty.
18
the date small non-road equipment engine is purchased
by the initial purchaser. If any emission-related part on
your engine is defective, the part will be replaced by
Hilti at no cost to the owner. Hilti shall remedy warranty
defects at authorized Hilti service and repair centers. Any
authorized work done at an authorized Hilti service and
repair center shall be free of charge to the owner if it
is determined that a warranted part is defective. Any
manufacturer-approved or equivalent replacement part
may be used for any warranty maintenance or repairs
on emission-related parts, and must be provided free of
charge to the owner if the part is still under warranty. Hilti
is liable for damages to other engine components caused
by the failure of a warranted part still under warranty. The
California Air Resources Board's Emission Warranty Part
List specifically defines the emission related, warranted
parts. These warranted parts are: the carburetor assem-
bly, coil assembly, rotor, spark plug, air filter, fuel filter,
breather manifold and the gaskets.
Maintenance requirements
The owner is responsible for performing the required
maintenance as defined by Hilti in the owner's manual.
Limitations
The Emission Control Systems Warranty shall not cover
any of the following: a) repair or replacement required
because of misuse, neglect or lack of required mainte-
nance, b) repairs improperly performed or replacements
not conforming to Hilti specifications that adversely affect
performance and/or durability, and alterations or mod-
ifications not recommended or approved in writing by
Hilti, and c) replacement of parts and other services and
adjustments necessary for required maintenance at and
after this first scheduled replacement point. Except as
set forth above, the warranty terms set forth in section
12 below, apply.
Additional claims are excluded, unless stringent na-
tional rules prohibit such exclusion. In particular, Hilti
is not obligated for direct, indirect, incidental or con-
sequential damages, losses or expenses in connec-
tion with, or by reason of, the use of, or inability to
use the tool for any purpose. Implied warranties of
merchantability or fitness for a particular purpose are
specifically excluded.
For repair or replacement, send the tool or related parts
immediately upon discovery of the defect to the address
of the local Hilti marketing organization provided.
This constitutes Hilti's entire obligation with regard to
warranty and supersedes all prior or contemporaneous
comments and oral or written agreements concerning
warranties.