Technical Data; Manufacturer's Warranty - Tools - Hilti WSC 85 Mode D'emploi

ORIGINAL OPERATING INSTRUCTIONS
WSC 85 hand-held circular saw
1 Cutting depth adjusting lever
2 Angle adjustment clamping screw
3 Parallel guide clamping screw
4 Cutting line indicator
5 Parallel guide
6 Baseplate
7 Inner clamping flange
8 Spindle
9 Riving knife
10 Spindle lockbutton
11 Screw
12 Clamping flange
13 Pivoting guard
14 Riving knife fastening screws
Manufacturer's warranty – tools
Hilti warrants that the tool supplied is free of defects in material and workmanship.
This warranty is valid so long as the tool is operated and handled correctly, cleaned
and serviced properly and in accordance with the Hilti Operating Instructions, and the
technical system is maintained. This means that only original Hilti consumables,
components and spare parts may be used in the tool.
This warranty provides the free-of-charge repair or replacement of defective parts only
over the entire lifespan of the tool. Parts requiring repair or replacement as a result of
normal wear and tear are not covered by this warranty.
Additional claims are excluded, unless stringent national rules prohibit such
exclusion. In particular, Hilti is not obligated for direct, indirect, incidental or
consequential damages, losses or expenses in connection with, or by reason of,
the use of, or inability to use the tool for any purpose. Implied warranties of
merchantability or fitness for a particular purpose are specifically excluded.
For repair or replacement, send tool or related parts immediately upon discovery of
the defect to the address of the local Hilti marketing organization provided.
This constitutes Hilti's entire obligation with regard to warranty and supersedes all
prior or contemporaneous comments and oral or written agreements concerning
warranties.
Printed: 08.07.2013 | Doc-Nr: PUB / 5071333 / 000 / 01
All manuals and user guides at all-guides.com
15 Extraction system adapter
16 Chip ejector
17 Switch-on interlock
18 On/off switch
19 Hexagon socket wrench
20 Ventilation slots
21 Cutting angle scale
22 Cutting depth scale
23 Cutting depth locking device
24 Auxiliary grip
The accompanying list of safety precautions
and the applicable regulations issued by your
trade association must be observed.

Technical data

Power input:
Power output:
Spindle speed under no load:
Spindle speed under load:
Blade peripheral speed under no load:
Blade peripheral speed under load:
Cutting depth at 0°:
Cutting depth at 45°:
Cutting depth at 60°:
Angular adjustment:
Maximum saw blade diameter:
Minimum saw blade diameter:
Blade mounting hole diameter:
Riving knife thickness (standard):
Dust extraction connector internal dia.:
Weight as per EPTA-Procedure 01/2003:
Protection class as per EN 60745
NOTE
The vibration emission level given in this information sheet has been measured in
accordance with a standardised test given in EN 60745 and may be used to compare
one tool with another. It may be used for a preliminary assessment of exposure. The
declared vibration emission level represents the main applications of the tool. However if
the tool is used for different applications, with different accessories or poorly
maintained, the vibration emission may differ. This may significantly increase the
exposure level over the total working period. An estimation of the level of exposure to
vibration should also take into account the times when the tool is switched off or when it
is running but not actually doing the job. This may significantly reduce the exposure
level over the total working period. Identify additional safety measures to protect the
operator from the effects of vibration such as: maintain the tool and the accessories,
keep the hands warm, organisation of work patterns.
Noise and vibration information (measured in accordance with EN 60745):
Typical A-weighted sound power level
Typical A-weighted emission sound pressure level
For the given sound power level as per EN 60745, the tolerance is 3 dB.
Wear ear protection!
1800 W (220–240 V); 1650 W (110 V)
1260 W (220–240 V)
4500/min.
3100/min.
54 m/sec.
37.3 m/sec.
0 to 85 mm
0 to 60 mm
0 to 43 mm
0° to 60°
230 mm
207 mm
30 mm
2.0 mm
35 mm
7.8 kg
Z / II
111 dB (A)
100 dB (A)
9