Maintenance Of The Spark Plug; Transport And Storage; Equipment Storage; Repair Service - stayer GID1000 Instructions D'emploi

To prevent carburettor malfunction, service the air cleaner
regularly.
Service more frequently when operating the generator in
extremely dirty areas.
Do not use gasoline or low flash point solvents for
cleaning. They are flammable and explosive under
certain conditions.
- Loosen the cover screw and remove the maintenance
cover.
- Remove the screw under the air filter box.
- Pull the air filter cover down 30mm and remove the air
filter cover.
- Remove the air filter iron clip and check the air filter
element. Clean or replace the element if necessary.
- Reinstall the air filter parts after cleaning or replacing
air filter element.

5.7 Maintenance of the spark plug

Please use high quality authentic spark plug. To ensure
proper engine operation, the spark plug must be properly
gapped and free of deposits.
- Remove the bolts on the panel and the controlling
panel.
- Take out the ignition coil rubber boot.
- Remove the spark plug with spark plug wrench.
- Visually inspect the spark plug. Discard it if the insulator
is cracked or chipped. Clean spark plug with a wire
brush if it is to be reused.
- Install the spark plug carefully by hand, to avoid cross-
threading.
- After a new spark plug has been seated by hand, it
should be tightened ½ turn with a wrench to compress
its washer. If a used plug is being reinstalled, it should
only require 1/8 to 1/4 turns after being seated.
- Reinstall the ignition coil rubber boot on the spark plug
securely.
- Reinstall the controlling panel.
The spark plug must be securely tightened. An
improperly tightened plug can become very hot
and possibly damage the generator.
Never use a spark plug with an improper heat range.

5.8 Transport and storage

To prevent fuel spillage when transporting or during
temporary storage, the generator should be secured
upright in its normal operating position, with the engine
switch OFF. The fuel cap vent lever is turned counter
clockwise to the OFF position. Allow the engine to cool well
before turning the fuel cap vent lever to the OFF position.
When transporting generator:
Do not overfill the tank. (there should be no fuel in the filler
neck)
Do not operate the generator while it is on a vehicle. Take
the generator off the vehicle and use it in a well ventilated
place.
ENGLISH
27
Avoid a place exposed to direct sunlight when putting the
generator on a vehicle. If the generator is left in an enclosed
vehicle for many hours, high temperature inside the vehicle
could cause fuel to vapor ze resulting in a possible
explosion.
Do not drive on a rough road for an extended period with the
generator on board. If you must transport the generator on
board. If you must transport the generator on a rough road,
drain the fuel from the generator beforehand.

5.9 Equipment storage

Before storing the unit for an extended period: Be sure
the storage area is free of excessive humidity and dust.
Drain the fuel.
Gasoline is extremely flammable and explosive
under certain conditions. Do not smoke or allow
flames or sparks in the area.
Completely drain the fuel from the tank. Open the fuel valve,
start the engine and operate it in the idle position until all
remaining fuel is gone and the engine stops automatically.
Discharge oil.
Remove spark plug and fill cylinder with 2cc's fresh oil. Pull
start motor 3-4 times to discharge the remaining oil. Then
reinstall the spark plug.
Pull the starting cord slowly until resistance is strong. At this
time, the piston is moving to the top of the compression
stroke and the valves will be closed.

5.10 Repair service

Our after-sales service responds to your questions
concerning maintenance and repair of your product as well
as spare parts. Exploded views and information on spare
parts can also be found under: info@grupostayer.com
Our customer consultants answer your questions
concerning best buy, application and adjustment of
products and accessories.

5.11 Warranty

Warranty card
Included in the documentation that accompanies this
equipment, you should find the warranty card. You should
fill out the card completely and return to vendor with a copy
of purchasing receipt or invoice and you should receive a
receipt.
Note: If you cannot find the warranty card within the
documentation, you must ask for it through your supplier.
The warranty is limited only to manufacturing defects and
expire if pieces have been removed or manipulated or
repaired other than the manufacturer.

5.12 Disposal and recycling

The machine, accessories and packaging should be sorted
for environmental-friendly recycling.
27