Publicité
Les langues disponibles
Les langues disponibles
1. Loosen the bevel lock knob
to override the 0° bevel stop.
2. When the saw is fully to the right, if the bevel pointer
indicate exactly 45°, turn the left 45° bevel adjustment screw
the 6 mm hex blade wrench
To adjust the left 45° bevel stop:
a. Loosen the bevel lock knob and tilt the head to the left.
b. If the bevel pointer does not indicate exactly 45°, turn the right 45°
bevel adjustment screw until the bevel pointer reads 45°.
Adjusting the Bevel Stop to 22.5° (or 30°) (Fig. A2, I)
nOTE: Adjust the bevel angles only after performing the 0° bevel angle and
bevel pointer adjustment.
To set the left 22.5° bevel angle, flip out the left 22.5° bevel pawl
31
Loosen the bevel lock knob
pointer
50
does not indicate exactly 22.5°, turn the crown adjustment
screw
51
contacting the pawl with a 10 mm wrench until the bevel pointer
reads 22.5°.
To adjust the right 22.5° bevel angle, flip out the right 22.5° bevel pawl.
Loosen the bevel lock knob and pull the 0° bevel stop
bevel stop. When the saw is fully to the right, if the bevel pointer does not
indicate exactly 22.5°, turn the crown adjustment screw
pawl with a 10 mm wrench until the bevel pointer indicates exactly 22.5°.
Fence Adjustment (Fig. A1)
The upper part of the fence can be adjusted to provide clearance, allowing
the saw to bevel to a full 49° both left and right.
11
1. To adjust each fence
, loosen the fence adjustment knob
slide the fence outward.
2. Make a dry run with the saw turned off and check for clearance.
3. Adjust the fence to be as close to the blade as practical to provide
maximum workpiece support, without interfering with arm up and
down movement.
4. Tighten the fence adjustment knob securely.
5. When the bevel operations are complete, relocate the fence.
For certain cuts, it may be desirable to bring the fences closer to the blade.
To do so, loosen the fence adjustment knobs
to the blade past the normal limit, then tighten the fence adjustment knobs.
Make a dry cut first to ensure the blade does not contact the fences.
For certain cuts it may be desirable to remove the sliding fence. To do so,
loosen the fence adjustment knobs
free of the base fence. The fence lanyard
removed completely from the saw or being lost. Once the cut is complete,
replace the sliding fence.
nOTE: The tracks of the fences can become clogged with sawdust. Use a
brush or some low pressure air to clear the guide grooves.
Guard Actuation and Visibility (Fig. X)
1
The lower guard
on your saw has been designed to automatically
uncover the blade when the arm is brought down and to cover the blade
when the arm is raised.
The guard can be raised by hand when installing or removing saw blades
or for inspection of the saw. NEVER RAISE THE lower GUARD MANUALLY
UN LESS THE BLADE IS STOPPED.
Rail Guide Adjustment (Fig. A1)
7
Regularly check the rails
for play or clearance.
The right rail can be adjusted with the set screw
use a 4 mm hex wrench and rotate the set screw clockwise gradually while
sliding the saw head back and forth.
Mitre Lock Adjustment (Fig. A1, M)
57
The mitre lock rod
should be adjusted if the table of the saw can be
moved when the mitre lock handle is locked (down).
19
1. Put the mitre lock handle
31
and pull the 0° bevel stop override
50
does not
29
until the bevel pointer indicates 45°.
and tilt the head fully to the left. If the bevel
32
to override the 0°
51
contacting the
10
and slide the fences closer
10
and slide the fence completely
36
prevents the fence from being
5
. To reduce clearance,
in the unlocked (up) position.
32
2. Using a 13 mm open end wrench, loosen the lock nut
lock rod.
3. Using a slotted screwdriver, tighten the mitre lock rod by turning it
55
with
clockwise as shown in Figure M. Turn the lock rod until it is snug, then
turn counterclockwise one turn.
4. Re-lock the mitre lock to a non-detented measurement on the mitre
scale – for example, 34° – and make sure the table will not rotate.
5. Tighten lock nut.
Prior to Operation
•
Install the base extensions to both sides of the saw's base. Refer to
Assembling the Base Extensions section.
•
Check the protective belt cover for damage and the proper functioning
53
.
of the lower guard.
•
Make sure to use the kerf plate. Do not operate the machine if the kerf
slot is wider than 12 mm.
•
Install the appropriate saw blade. Do not use excessively worn blades.
The maximum rotation speed of the tool must not exceed that of the
saw blade.
•
Make sure all locking knobs and clamp handles are tight.
•
Use personal protective equipment and connect the saw to an external
dust extractor.
•
Although this saw will cut wood and many nonferrous materials, these
operating instructions refer to the cutting of wood only. The same
guidelines apply to the other materials. Do not cut ferrous (iron and
steel) materials, fibre cement or masonry with this saw!
10
and
•
Do not attempt to cut excessively small pieces.
•
Secure the workpiece.
•
Allow the blade to cut freely. Do not force.
•
Allow the motor to reach full speed before cutting.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of injury, turn unit off and
disconnect machine from power source before installing and
removing accessories, before adjusting or changing set-ups
or when making repairs. Be sure the trigger switch is in the OFF
position. An accidental start-up can cause injury.
Refer to Saw Blades under Optional Accessories to select the blade that
best fits your needs.
Ensure the machine is placed to satisfy your ergonomic conditions in terms
of table height and stability. The machine site shall be chosen so that the
operator has a good overview and enough free surrounding space around
the machine that allows handling of the workpiece without any restrictions.
To reduce effects of vibration, make sure the environment temperature is
not too cold, the machine and accessories are well maintained and the
workpiece size is suitable for this machine.
Be sure the cord will not interfere with your work.
Proper Body and Hand Position (Fig. N1, N2)
WARNING: To reduce the risk of serious personal injury, ALWAYS use
proper hand position as shown in Figure N1.
WARNING: To reduce the risk of serious personal injury, ALWAYS hold
securely in anticipation of a sudden reaction.
•
Never place hands near cutting area. Place hands no closer than
100 mm from the blade.
•
Hold the workpiece tightly to the table and the fence when cutting.
Keep hands in position until the trigger has been released and the blade
has completely stopped.
EnGLISh
58
on the mitre
41
Publicité
