DeWalt DWS780N Traduction De La Notice D'instructions Originale page 40

EnGLISh
area, and work with approved safety equipment, such as those dust masks
that are specially designed to filter out microscopic particles.
Avoid prolonged contact with dust from power sanding, sawing,
•
grinding, drilling, and other construction activities. Wear protective
clothing and wash exposed areas with soap and water. Allowing dust to
get into your mouth, eyes, or lay on the skin may promote absorption of
harmful chemicals.

WARNING: Use of this tool can generate and/or disperse dust, which
may cause serious and permanent respiratory or other injury. Always
use approved respiratory protection appropriate for the dust exposure.

WARNING: We recommend the use of a residual current device with a
residual current rating of 30mA or less.
Residual Risks
The following risks are inherent to the use of saws:
• Injuries caused by touching the rotating parts.
In spite of the application of the relevant safety regulations and the
implementation of safety devices, certain residual risks cannot be avoided.
These are:
• Impairment of hearing.
• Risk of accidents caused by the uncovered parts of the rotating saw blade.
• Risk of injury when changing the blade.
• Risk of squeezing fingers when opening the guards.
• Health hazards caused by breathing dust developed when sawing wood,
especially oak, beech and MDF.
The following factors increase the risk of breathing problems:
• No dust extractor connected when sawing wood.
• Insufficient dust extraction caused by uncleaned exhaust filters.
Electrical Safety
The electric motor has been designed for one voltage only. Always check
that the power supply corresponds to the voltage on the rating plate.
Your D WALT tool is double insulated in accordance with
e
EN62841; therefore no earth wire is required.
If the supply cord is damaged, it must be replaced only by D
authorised service organisation.
Mains Plug Replacement (U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in the plug.
• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved 3–core extension cable
suitable for the power input of this tool (see Technical Data).The minimum
conductor size is 1.5 mm ; the maximum length is 30 m.
2
When using a cable reel, always unwind the cable completely.
Package Contents
The package contains:
1 Assembled mitre saw
2 Base extentions and installation hardware
1 Blade wrench (see placement in Fig. A2)
1 Saw blade
1 Dustbag
1 Material clamp
1 Instruction manual
38
• Check for damage to the tool, parts or accessories which may have
occurred during transport.
• Take the time to thoroughly read and understand this manual prior
to operation.
Markings on Tool
The following pictograms are shown on the tool:
Date Code Position (Fig. A1)
The date code
into the housing.
Example:
Description (Fig. A1–E)

WARNING: Never modify the power tool or any part of it. Damage or
WALT or an
e
personal injury could result.
Fig. A1
1 Lower guard
2 Operating handle
3 Carrying handle
4 Rail lock knob
5 Rail set screw adjustment
6 Date code
7 Rails
8 Bevel scale
9 Lock down pin
10 Fence adjustment knob
11 Fence
12 Base fence
13 Base extension handles
14 Hand indentation
15 Table
16 Bench mounting holes
17 Mitre scale
18
Dust duct inlet
19 Mitre lock handle
20 Mitre latch button
21 Kerf plate
Fig. A2
22 Trigger switch
23 Lock-off lever
Read instruction manual before use.
Wear ear protection.
Wear eye protection.
Keep hands away from blade.
Keep hands 100 mm from either side of saw blade.
Do not stare directly into the light source.
Carrying point.
6
, which also includes the year of manufacture, is printed
2022 XX XX
Year of Manufacture
24 Padlock hole
25 XPS on/off switch
26 Wing nut
27 Depth adjustment screw
28 Grooving stop
29 Blade wrench
30 Base
31 Bevel lock knob
32 0° bevel stop override
33 Dust extraction port
34 Belt cover
35 Electronic speed control dial
(DWS780 Only)
36 Fence lanyard
37 Workpiece clamp (Fig. B)
Optional accessories
Fig. C
38 DW7053-XJ Dustbag
Fig. D
39 DE7023-XJ / DE7033-XJ Leg stand
Fig. E
40 DE7025-XJ Clamp brackets