Publicité
Les langues disponibles
Les langues disponibles
Replacement of the slide locking ring
The slide locking ring is the seal between the pump body
and the engine shaft. The ring is a component with natural
wear and tear.
If the slide locking ring is defective, water leaks between the
engine and the pump body. Demount the pump body,
manual starting device and the pump moving wheel. Then,
the slide locking ring may be replaced. Finally, carefully
mount the moving wheel of the pump, manual starting
device and the pump body.
Removal of foreign particles from the pump
Coarser particles in the pumped liquid may block the pump
body and the pump moving wheel. For this case, the pump
body can be demounted in order to remove all impurities
from the pump moving wheel.
Storing
If the machine is not used for longer time, all water in the
pump must be drained. Let the pump dry to avoid corrosion.
Drain the fuel tank and the carburettor. Cleaning and
preserving of the machine before storing is recommended.
Make sure the machine is stored in dry and frost-proof
place.
Failures
Make sure no water gets in the machine.
We shall not be liable for damage due to
unprofessional repair attempts. Damage due to
unprofessional repair attempts shall void any warranty
claims.
All measures for removal of defects may be performed only
if the engine is stopped.
The following list specifies some potential machine
damages, potential reasons and tips for removal. All
measures for removal of defects may be performed only if
the engine is stopped. If you are unable to remedy the
defect, please contact either the customer service or your
sales representative. Overhaul repairs may be performed
by authorized personnel only. Please note that warranty
claims shall void in case of damage due to unprofessional
repair attempts and we shall not be responsible for any
consequent damage.
In case of operation failures, first check for operator error or
other cause not associated with the machine defect - e.g.
no fuel.
Maintenance table
Defect
Possible cause
The pump
1.
Too much liquid
does not
in the pump.
pump or
pumps too
little of
2.
Suction piping
liquid, the
not sealing.
engine runs.
3.
Too low engine
power selected.
4.
Suction piping
input filter
clogged.
5.
Suction piping
clogged.
Remedy
1.
Pour liquid in
the filling hole
of the pump
body.
2.
Tighten the
suction piping
and piping
connectors with
Teflon tape.
Replace the
suction piping if
irreparable
damage is
detected.
3.
Increase
engine power.
4.
Clean the filter.
5.
Clean the
suction piping.
15
6.
Pump moving
wheel blocked
by impurities.
7.
Too high suction
lift/total head.
8.
Defective slide
locking ring.
9.
Pump moving
wheel not fitted
correctly.
10. Damaged pump
moving wheel.
11. Irregular engine
operation.
Vibration or
1. Too high suction
noisy
lift/total head.
operation
2. Foreign particle
blocks the suction
piping and/or the
pump moving
wheel.
3. Unstable
installation.
4. Unstable machine
installation.
5. Damaged pump
moving wheel.
6. Other technical
defect.
The engine
1.
Low fuel.
does not
start or turns
off during
2.
No ignition
operation.
spark.
3.
Clogged
carburettor.
4.
Clogged air
filter.
5.
Activated Auto
Stop because of
low engine oil
level.
6.
Other technical
defect.
6.
Remove
impurities.
7.
Change the
installation so
that the suction
lift/total head
does not
exceed
maximum
value.
8.
Replace the
slide locking
ring.
9.
Place the pump
moving wheel
correctly.
10. Replace the
pump moving
wheel.
11. Contact the
customer
service.
1.
Change the
installation so
that the suction
lift/total head
does not
exceed
maximum
value.
2.
Remove
foreign particle.
3.
Stabilize the
installation.
4.
Ensure stable
position of the
machine.
5.
Replace the
pump moving
wheel.
6.
Contact the
customer
service.
1.
Open the
gasoline cock
and/or refuel.
2.
Check the
ignition switch.
Or check the
ignition plugs.
3.
Clean the
carburettor.
4.
Clean air filter.
5.
Replenish
engine oil.
6.
Contact the
customer
service.
Publicité
